For each problem, one curved surface is shown restraining a body of static fluid. Compute the magnitude of the horizontal component of the force, and compute the vertical component of the force exerted by the fluid on that surface. Then, compute the magnitude of the resultant force and its direction. Show the resultant force acting on the curved surface. In each case the surface of interest is a portion of a cylinder with the length of the surface given in the problem. Referring to figure 5, the surface if 2.00 long. Water 1.85m 0.75m radius

For each problem, one curved surface is shown restraining a body of static fluid. Compute the magnitude of the horizontal component of the force, and compute the vertical component of the force exerted by the fluid on that surface. Then, compute the magnitude of the resultant force and its direction. Show the resultant force acting on the curved surface. In each case the surface of interest is a portion of a cylinder with the length of the surface given in the problem. Referring to figure 5, the surface if 2.00 long. Water 1.85m 0.75m radius

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A frictionless pulley system is designed as shown. The mass (at right) is 92 kg., and the spring has a spring constant, k = 19 N/mm, and is stretched from its original length 9 cm. When the system is in equilibrium, what is the angle a? mass block
Problem 5
Consider the beam shown in (Figure 1). Suppose that a = 100 mm, b = 30 mm, and r = 200 mm. b 45° 45° b C 45% 45° Determine the moment of inertia for the beam's cross-sectional area about the x? axis passing through the centroid C of the cross section.
3.Statistics of Regid Bodies/ Civil Engineering
A thin plate with a size of 20 cm x 20 cm, with a constant speed of 1.0 m/S between two walls and F it is drawn in the direction in which it is seen in the figure with its force. The distance between the walls is 3.6 mm, and the wall at the top is fixed, and the wall at the bottom is on the left side it is moving at accurate 0.3 M /s constant speed. Fluid viscosity between walls 0.027 Pa.sn and since the velocity distribution is linear (linear) ; a) draw the speed distribution profile, determine where the speed is "0". b) calculate the "F" force that will pull the plate at a constant speed of 1.0 m/s. Fixed Wall = I mm V= 1 m/s F h2 = 2.6 mmi V. = 0.3 m / s Movable Wall
DYNAMICS OF RIGID BODIES. Show complete solution
Please help solve
Two pull cables are used to support the telephone pole, as shows the figure below. Express the FA and FB forces as Cartesian vectors and show the angle between the two forces.
The very important load on a structure is the pressure load.Loading is simplified for mathematical calculations as a parabola.In the case of a horizontal solid, the pressure force is distributed in a non-linear, parabolic fashion, as shown in the figure.The greatest force is located on the support A and is given as the letter Y in kilonewton per meter (kN / m) and its total length as the letter X in meters (m).This structure is shown below, calculate as support reactions at points A and B. (Disregard the proper weight of the steel beam) X = 10m Y = 100 kN / m
Problem 4.39 Consider the system shown in (Figure 1). Figure 1 of 1 45° 7 ft F= 80 lb 3 ft B 1.5 ft < 5 ft 401 1.5 ft D x1 Part A Determine the moment of the force F about the door hinge at B. Express the result as a Cartesian vector. Express your answer in terms of the unit vectors i, j, and k. Use the 'vec' button to denote vectors in your answers. Express your answer using three significant figures. Π ΑΣΦ ↓↑ vec MB = Submit My Answers Give Up Incorrect; Try Again; 3 attempts remaining ? N.m Provide Feedback Continue