For class AB amplifier the R.M.S. input voltage is IIV and the supply voltage is £20V and the laod resistance (842) assume B-100 and VBE-0.8V, find the current through the diode, the power dissipated in the load, the power drawn by the supply. the dissipated power at each transistor, and the conversion efficiency?

For class AB amplifier the R.M.S. input voltage is IIV and the supply voltage is £20V and the laod resistance (842) assume B-100 and VBE-0.8V, find the current through the diode, the power dissipated in the load, the power drawn by the supply. the dissipated power at each transistor, and the conversion efficiency?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The amplifier in the circuit below is driven by a signal generator v, with a small sine wave signal vhose average value is zero. Assume the transistor has a value of B-100, and V-26 mV. a. You need to design the circuit so that the de emitter current IE of the emitter resistor RE to establish the desired de emitter current. = 1 mA. Specify the value b. A de collector voltage of +5 volts is desired. Specify the value of the collector resistor Re to establish the desired de collector voltage. For this part assume that RL 5 K and the Early Effect needs to be considered. The transistor has a VA 100 Volts. Draw the ac small signal equivalent circuit model of the amplifier and determine its voltage gain. 91SV C. 2.5k MM do RE -15 V 84 Vout RL
Example 8:-
Using the re model circuit, determine the total voltage gain for the BJT circuit shown below. Show the details of your work. 22V ... 5.6k0 330k Vo + 10UF-POL B = 80 1200 10UF-POL To = 40 kN 2N2221 6.8k) Vs 4700 22UF-POL
5. The fixed bias circuit shown in figure uses a silicon transistor with VBE = 0.7V. (a) Find the collector current, lc, and voltage VCE, if ß of transistor is 60. (b) (b) Find Ic and VCE if B changes to 80. +Vcc (9V) 60k 0.5k + VCE VBE
Given zener voltage at 9V, input voltage at 12Vdc to 15Vdc and ILmax at 40mA. What is Rsmin if Izmax rated is 50mA?
The input voltage of a Boost converter is 10V, the duty cycle of the boost converter is 0.25. If a 10- ohm resistor load is connected to the output; what are the average current flowing in the MOSFET and the diode? what is the max voltage stress on the MOSFET and the diode?
8.
A. Detemine the value of the collector resistor in an npn transistor amplifier with Ppc = 250, VBB = 2.5 V, Vcc = 9 V, VCE = 4 V, and Rg = 100 k2. B. Detemine Icsat) for the transistor in below Figure. What is the value of IB necessary to produce saturation? What minimum value of VIN is necessary for saturation? Assume %3D VCE(sat) = 0 V. +5 V 10 kN Rg VINO BDc = 150 1.0 MN
Q9. Draw Zener regulator circuit to obtain regulated DC voltage 6.8 V. Considering input DC voltage in the range from 10V to 30V. Consider load resistance of 110KQ. Q10. Determine maximum and minimum value of Zener current if value of series resistance is 1 K, load resistance is 2KN and input varies from 10V to 30V. Zener voltage is 5 V. Q11. What is LED?
Q4. For the circuit shown in Figure Q4: i) What is the type of MOSFET and the amplifier configuration? ii) Find the Q-point (Ip and Vps) iii) What is the device transconductance, gm? iv) What are the voltage gain and output voltage? v) Draw the input /output voltage waveforms showing the phase relationship between them. Be sure to label them properly. +20V IDON = 15 mA@ VcsON = 6V VGSTH = 1V 1kQ Rp C2 10M2 Ro1 out Vin 3.3MQ Ra, 47003 Rs 50mV Figure Q4
Correct the sentence: The aim of using coupling in multistage transistor amplifiers is to transfer DC output of one stage to the input of the next .stage and to isolate the d.c. conditions of one stage from the next stage
Please solve it.