For carbon steel casting with step pattern shown in Figure 1, that all surfaces will be machined after casting process, considering fraction coefficient to be 0.4 and density .to be 7.8 g/cm3 and Gating ratio to be 1.4: 1.2: 1 .Calculate for 4 pieces in one mold. Determine and draw a) pattern design b) Riser design c) Gating design 150mm 150mm 40 mm 130 mm 40 mm 500 mm

For carbon steel casting with step pattern shown in Figure 1, that all surfaces will be machined after casting process, considering fraction coefficient to be 0.4 and density .to be 7.8 g/cm3 and Gating ratio to be 1.4: 1.2: 1 .Calculate for 4 pieces in one mold. Determine and draw a) pattern design b) Riser design c) Gating design 150mm 150mm 40 mm 130 mm 40 mm 500 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem 2 Consider the casting of the 2mm thick object below shown in its top view. If one riser with D =H = 6.5 mm is needed for this casting, illustrate where the riser should be located to produce a sound casting. Is this possible with no chills? Hint: use your illustration to justify. If no risers were used, illustrate where the shrinkage defects would likely occur. Tip: Using Word's/Powerpoint's basic shapes will be helpful here. 12.5 mm 10 mm 6.2 mm
Situation 5: The compound bar, composed of the three segments shown, is initially stress free. Compute the stress in each material if the temperature drops 25°C. Assume that the walls do not yield and use the following data: A (mm²) a (/*C) E (GPa) Bronze segment 2000 19.0 x 10-6 83 Aluminum segrnent 1400 23.0 x 10-6 70 Steel segment 800 11.7 x 10- 200 - 500 mm→- 400 mm- 800 mm Aluminum Steel Bronze 17. Compute the stress in the bronze bar a. 31.6 MPa (T) b. 31.6 MPа (С) 18. Compute the stress in the aluminum bar. а. 45.1 MPа (Т) b. 45.1 MPa (C) 19. Compute the stress in the steel bar. 79.0MPA (T) 79.0MPA (C) 13.6 MPa (T) 13.6 MPa (C) c. d. 54.1 MPа (Т) 54.1 MPa (C) с. d. a. C. 97.0 MPa (T) b. d. 97.0 MPa (C)
Determine the compressive force (in lb) in the bars shown after a temperature rise of 173°F if d = 0.015 in. Round off the final answer to five decimal places. Use the following data: Bronze Aluminum A = 2.24 sq. in A = 2.78 sq. in E = 14959726 psi E = 10594540 psi L = 12.5 in L = 16.6 in α = 11.61 x 10-6/ °F α = 12.67 x 10-6/°F
Please help I need it in 30 minutes
Find the value of p
Date: Course: Time: Pind the vertical movement os is 120 KN Stsel Aluminum 3 m Im B P=120 kat Aluminum A = 900 mm² E = 70 GN m² steel A= 600 mm E 200 GNM² %3D
In the figure below, the wood pole is supported by cables of 0.32-in diameter. The turnbuckles in the cables are tightened until the stress in the cables reaches 60000psi. If the working compressive stress for the wood is 216psi. Determine the smallest permissible diameter of the pole.___________inches in 2 decimal places. Take note: Write it on a paper, hand written showing answer. Thanks
i need the answer quickly