For a simply supported prestressed concrete beam, compute the stress in the top fiber due to initial prestressing force and service loads. Properties of the beam are: Width of the beam, b: 204 mm; Depth of the beam, d: 475 mm; Concrete cover of the beam, cc: 43 mm; Prestressing Force, P: 686 KN; Superimposed Load, w: 11 KN/m; Length of the beam, L: 14 m; Weight of Concrete: 23.5 KN/m3. Stress is in unit MPa. Write only the value of your final answer. (not including saitonighe to

For a simply supported prestressed concrete beam, compute the stress in the top fiber due to initial prestressing force and service loads. Properties of the beam are: Width of the beam, b: 204 mm; Depth of the beam, d: 475 mm; Concrete cover of the beam, cc: 43 mm; Prestressing Force, P: 686 KN; Superimposed Load, w: 11 KN/m; Length of the beam, L: 14 m; Weight of Concrete: 23.5 KN/m3. Stress is in unit MPa. Write only the value of your final answer. (not including saitonighe to

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A group of concrete cubes mixed with different water ratios .. The group with water ratio W / c = 0.3The maximum load was testedFailure causes every cube in the group Required:1- Finding the stress rate for each group in unit N / mm2 with discussing the results and the effect of the water w / c ratio on the compressive strength of the group.
Please give me the correct solutions and answer of this problem in principles of reinforced/prestressed concrete
A half-block concrete masonry unit is subjected to compression until failure.The outside dimensions of the specimen are 190 mm X 190 mm X 190 mm.The cross section is a hollow square with a wall thickness of 38 mm. The loadis applied perpendicular to the hollow cross section and the maximum loadis 296 kN.a. Determine the gross area compressive strength.b. Determine the net area compressive strength.
Subject: Reinforced Concrete Structures exam
Given Data: Concrete dimensions Area of steel 625 560 f = 30 MPa ЗHD25 f, = 420 MPa A, = 2457 mm² 65 %3D b = 250 Required: What is the maximum uniformly distributed live load it can support in addition to dead load?
A simply supported beam 6.5m long, 350mmx500mm, prestressed with a straight tendon located 150mm below the neutral axis with effective prestressing force, Pe, of 300kN. Total load carried by the beam is 20kN/m. A. Determine the area of the concrete, mm2.B. Determine the section modulus of the concrete in x10^3 mm^3C. Determine the compressive stress caused by the tendon alone if Pe is at the centroid, MPa
Find the minimum theoretical width and height of a rectangular concrete section that will make the beam failure sufficiently ductile. Given: Two layers of 2-Ø25 mm bottom reinforcements fy=414 MPa f'c=35 MPa stirrup diameter=minimum required clear cover=minimum value for beam vertical clear spacing bet. Iayers=minimum value for beam height-to-width ratio=2.0 Note: Ductile failure occurs in beams when the extreme reinforcement layer is strained to 0.004 or greater.
just answer d to f
CAN SOMEONE HELP ME SOLVE THIS REINFORCED/PRESTRESSED CONCRETE PROBLEM. USE NSCP 2015 A concrete beam has a width of 304.8 mm and an effective depth of 495.3 mm. It is reinforced with 14.194 cm2 steel bars with fc′ = 17,237.5 kPa (n = 10). Determine the flexural stresses caused by a bending moment of 84.1 kN·m
Q.1\ A column of a cross-section (350x450)mm is reinforced with 4 bars of (25mm) in diam., knowing that Es=200,000MPa and Ec 22,500MPa and f28MPa and fy = 420 MPa determine the following: 1. The axial load that will stress the concrete to 10 MPa. 2. The normal axial compression strength.
please answer in the nearest 3 decimal numbers
Correct solution