For a physics lab assignment, a student needs to create a solenoid using copper wire with diameter d= 0.500 mm. Theresistance of the solenoid needs to be 4.30 0 and the magnetic field of the solenoid with a current of 2.10 A should be5.70 x 10 T. Assume the resistance does not change significantly with temperature, and the radius of the solenoid is1.00 cm. (Use p= 1.70 x 107 -8Om for the resistivity of copper.)(a) How many turns of wire does the student need?turns(b) Determine the required length (in cm) of the solenoid.cm

Given, Diameter of copper wire (d) = 0.500 mm Resistance of solenoid (R) = 4.30 Ω Current in…

Answered: For a physics lab assignment, a student…

Similar questions

A solenoid with 4 x 107 turns/m has an iron core placed in it whose magnetic susceptibility is 4.0 × 103 . (a) If a current of 2.0 A flows through the solenoid, what is the magnetic field in the iron core? (b) What is the effective surface current formed by the aligned atomic current loops in the iron core? (c) What is the self-inductance of the filled solenoid?
An MRI technician moves her hand from a region of very low magnetic field strength ( approximately zero) into the MRI scanner's field in a quick motion, taking 3.1 milliseconds. The MRI is essentially a solenoid, with 1500 loops of wire. By doing so, a current of 0.15 milliAmps is induced in her wedding ring. If her wedding ring has a diameter of 1.95 cm and it has measured resistance of 119 Ohms, what is the magnetic field in the MRI.
For a technical application, an electrical engineer needs to create a solenoid using copper wire with diameter d = 0.500 mm. The resistance of the solenoid needs to be 5.10 2 and the magnetic field of the solenoid with a current of 3.10 A should be 5.90 x 10-2 T. Assume the resistance does not change significantly with temperature, and the radius of the solenoid is 1.00 cm. (Use p = 1.70 x 1080 m for the resistivity of copper.) (a) How many turns of wire does the electrical engineer need? turns (b) Determine the required length (in cm) of the solenoid. cm
For a physics lab assignment, a student needs to create a solenoid using copper wire with diameter d = 0.500 mm. The resistance of the solenoid needs to be 3.50 and the magnetic field of the solenoid with a current of 2.90 A should be 5.90 × 10-² T. Assume the resistance does not change significantly with temperature, and the radius of the solenoid is 1.00 cm. (Use p 1.70 x 10-8.m for the resistivity of copper.) (a) How many turns of wire does the student need? turns (b) Determine the required length (in cm) of the solenoid. cm
Find the flux of the Earth's magnetic field of magnitude 5.00 ✕ 10-5 T, through a square loop of area 30.0 cm2 for the following. (a) when the field is perpendicular to the plane of the loop T·m2(b) when the field makes a 30.0° angle with the normal to the plane of the loop T·m2(c) when the field makes a 90.0° angle with the normal to the plane T·m2
How much current must pass through a horizontal power transmission cable in order for the magnetic field at a location 21 m directly below it to be equal to the Earth's magnetic field, which is approximately 8.0 x 10-5 T? Express your answer to two significant figures and include appropriate units. Value Units ?
A circular conducting loop with a radius of 1.00 m and a small gap filled with a 10.0 resistor is oriented in the xy-pane. If a magnetic field of 2.0 T, making an angle of 30° with the z-axis increases to 9.0 T, in 2.0 s, what is the magnitude of the current that will be caused to flow in the conductor?
It is desired to construct a solenoid that will have a resistance of 5.60 N (at 20°C) and produce a magnetic field of 4.00 X 10¬2T at its center when it carries a current of 3.10 A. The solenoid is to be constructed from copper wire having a diameter of 0.500 mm. If the radius of the solenoid is to be 1.00 cm, determine the following. (The resistivity of copper at 20°C is 1.7 × 10-8 0· m.) (a) the number of turns of wire needed to build the solenoid 1029 v turns (b) the length the solenoid should have X cm 1.034*10**7
It is desired to construct a solenoid that will have a resistance of 4.15 2 (at 20°C) and produce a magnetic field of 4.00 x 10-2 T at its center when it carries a current of 5.00 A. The solenoid is to be constructed from copper wire having a diameter of 0.500 mm. If the radius of the solenoid is to be 1.00 cm, determine the following. (The resistivity of copper at 20°C is 1.7 x 10-8 0 • m.) (a) the number of turns of wire needed to build the solenoid turns (b) the length the solenoid should have cm
You are working at a company that manufactures solenoids for industrial and research use. A client has ordered a solenoid that will be operated by a 1,000 V power supply and must be of length { = 36.0 cm. A cylindrical experimental package of radius r. = 1.85 cm must fit inside the solenoid. The client wants the largest possible magnetic field inside the solenoid. The thinnest copper wires allowed by your company are AWG 36, which corresponds to a wire diameter of d, = 0.127 mm. You determine the maximum magnitude of magnetic field (in T) that can be created in the solenoid to report to the client. (The resistivity of copper is 1.7 x 10-80: m.)