I need the answer quickly For a particular semiconductor sample,hole concentration p, = 1013e-x/Lr cm for x 2 0, L, = 2 x 10-3 cm;electron concentration n, = 2 x 1014e-*/ln cm for x 2 0, L, = 1 x 10-4 cm;D, = 20; D, = 10 . The total current density at x = 0 and x = 1 um respectivelycm?areO 320 A/cm² and 8 A/cm?О 320 A/ст? and 8 A/ст?0 0.65 A/ст? and 3 A/cт?O 3.2 A/cm? and 4 A/cm?

The total current is given byJn=eDndndx-eDpdpdx

For a particular semiconductor sample, hole concentration p, = 103e-/Lr cm for x 2 0, L, = 2 x 10-3 cm; electron concentration n, = 2 x 101e-/la cm³ for x 2 0, L, = 1x 10- cm; D, = 20: D. = 10. The total current density at x = 0 and x = 1 um respectively are O 320 A/cm² and 8 A/cm? 320 A/cm² and 8 A/cm² O 3.2 A/cm² and 4 A/cm2 O 0.65 A/cm² and 3 A/cm?

For a particular semiconductor sample, hole concentration p, = 103e-/Lr cm for x 2 0, L, = 2 x 10-3 cm; electron concentration n, = 2 x 101e-/la cm³ for x 2 0, L, = 1x 10- cm; D, = 20: D. = 10. The total current density at x = 0 and x = 1 um respectively are O 320 A/cm² and 8 A/cm? 320 A/cm² and 8 A/cm² O 3.2 A/cm² and 4 A/cm2 O 0.65 A/cm² and 3 A/cm?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

If an electrical system operates at a potential higher than 600 volts, the nonmetallic conduit must be encased in at least_of concrete. A. 1 inch B. 2 inches C. 4 inches D. 6 inches
COLUMN A COLUMN B A copper wiring containing 8 color-coded 1. conductors or 4 twisted pairs that offers greater bandwidth for local area networks. A. LEGEND 2. distribution device. A wiring pattern that connects to a central B. HOMERUN 3. Another term for an 8-pin modular jack. C. OVERCURRENT 4. A coaxial cable quad shielded with all copper center conductor used for cable TV. D. INSULATOR It is the maximum current that a conductor can 5. carry without exceeding its temperature rating. E. SHORT CIRCUIT 6. A wiring job where many cables enter a device or a junction box that is considered an unsafe practice in electrical wiring, F. CIRCUIT BREAKER 7. An electrical safety device designed to protect an electrical circuit from damage. G. ARC FLASH 8. unintended path with very low resistance. Occurs when an electrical current flows in an H. AMPACITY 9. amperage capacity of the circuit. Occurs when the current exceeds the rated I. UTP 10. A method of extending an electrical wire to the ground…
Can you finish the Background including a synopsis of the relevant information of this this example "electrical maintenance and repair" And please cite an article or paraphrase of author. Thank you! The electrical wiring and electrical devices in the houses that are installed may have failure so the inspection is designed to definitely perform the clear capabilities. These electrical devices are...
Question.
What is the total number of systems?
3. Which of the following statements about the use of structural steel as an equipment grounding conductor(EGC) in an AC system is correct?A. Structural steel isn't allowed for use as an EGC.B. Structural steel can be used as an EGC bonding jumper between panelboards.C. Structural steel must have an EGC bonding jumper every three feet of structure.D. Structural steel can be used as an EGC when it's bonded at both ends.
The contractor is controlled by?
Assuming all terminals are rated 75°C and you have a #10 AWG THHN/THWN conductors in a conduit and the conduit is run on the roof off a office building where the ambient temperature never rises above 30°C the largest size circuit breaker or fuse permitted to protect these wires is:?
The wording that I am running into with questions such as "The number of conductors required to be installed between three-way and four-way switches is " is confusing. The text is not expalining this in a way that I am understanding anything other than grounding conductor, which is optional unless I am using a metal box. So what type of "conductor" is beng discussed?
Complete the following text with words Pt100 sensors are a specific type of _____(1) detector. The most important characteristic of Pt100 elements is that they are made of _____(2) with an electrical resistance of _____(3) ohms at a temperature of ______(4) °C and temperature coefficient ____(5). It is by far the most common type of RTD sensor. The other materials with which RTDs are built are: ___(6), _____(7), ______(8). The most recommended conditioning method is reading at _____(9). Typically, a _____(10) behavior of the Resistance-Temperature relationship can be assumed.
Please answer quickly. 17. The filament of incandescent lamp is usually made of: a. copper b. silver c. aluminum d. tungsten 18. A current measuring instrument can be modified to measure voltages by: a. using thicker wire in the coil b. using a high resistance shunt c. adding resistance in series d. adding resistance in parallel 21. "When two power sources are connected in a series-aiding configuration, the output voltage equals the _____________" a. supply with the highest voltage b. supply with the lowest voltage c. difference of the two supplies d. sum of the two supplies
I need the answer at 20 minute.