For a constant force, a rope breaks due to stress. Which of the following is useful to reduce the stress? a) Increase the length of the rop b) Apply small forc c) Increase the cross sectional area of the rop d) Use a different material of rope,eeerope

Q: A 463-N object is hung from the end of a wire of cross-sectional area 0.03 cm-. The wire stretches…

A:

Q: 3 a P M The scheme of supporting of the absolutely rigid body is shown in the picture. Define the…

A: Answer..

Q: Two waves of the same frequency have amplitudes 1.38 and 2.85. They interfere at a point where their…

A: When two waves of same frequency superpose, amplitude of resultant  of two waves depends upon the…

Q: 5. (a) Explain the differences in edge and screw dislocations. (b) Locate your screw dislocation at…

A: A) Edge and screw dislocations are two types of crystal lattice defects that can occur in materials.…

Q: Identify the tensile strength/elasticity and choose which is the best banana variety that can be…

A: Tensile strength refers to the amount of force a material can withstand before breaking under…

Q: i need to know how they got the value of 52.89 from the eqaution

A: Given Data : Y = 1.12 a = 0.1 mm = 10-1 mm  K1c = 1.05MPa.m0.5 To Find :  Part (b) how to get the…

Q: You are designing a method to help lift a 1,956 lbf rocket (1 ton) for transportation. You are…

A: Given that Force,W=1906 lbfyeild strength,σy=50 ksi=50×1000=50000 psifactor of safety,fos=2Minor dia…

Q: Which type of stress occurs when an external force tends to twist or distort an object along a plane…

A: Note:- When a body is subjected to external force than deformations occur in it, to restore it into…

Q: What happens when the stress applied to the body is increased beyond the maximum value and is…

A:

Q: If the allowable stress is equivalent to the actual stress, the factor of safety is 0. True False

A: We know that factor of safety is the ratio of allowable stress to the actual stress, Factor of…

Q: QUESTION 16 The T-beam is made of a nylon. The allowable stress is 24 MPa in tension and 30 MPa in…

A: The area of the top section will be, A1=80×30 ⇒A1=2400 mm2 And the area of the bottom section will…

Q: What is the modulus of elasticity? a) Ratio of elongation of a material to the original length b) It…

A: When a force is applied in a particular area, the modulus of elasticity measures the object's…

Q: Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

A: Solution:-Given that

Q: Suppose we wish to develop a super-ox in which all dimensions (including those of the legs) are…

A:

Q: A strain gauge is a type of sensor used in a wide variety of applications to measure the strain of…

A:

Q: me rigid pipe is supported by a pin at A and an A-36 steel guy wire BD gure Part A 4 ft био μA B…

A: Have a look

Q: Figure shows the stress versus strain plot for a material that is stretched by a machine pulling in…

A:

Q: A.) A force stretches a wire by 4.0 mm. A second wire of the same material has the same cross…

A: Let the force applied is F. Let the area be A. Let the change in length be ∆L  Let the original…

Q: A Strain Strain Stress Stress B.

A: Correct option is A  i e material A is stronger than B .

Q: A one metre long circular concrete beam, diameter 400mm, supports a 10kN load in the middle and is…

A: We know that the tensile stress is given by,Now, the given concrete beam is a cylindrical structure…

Q: A Human arm model as shown is lifting a Weight W. Determine the stress developed in the bicep muscle…

A:

Q: Mechanical stress is Select one: O a. a change in the relative position of the points of the body,…

A: Mechanical stress is defined as  force per unit area , when a load is applied to the material .…

Q: You hang a ball from a wire with cross-sectional area 0.01 m². If the tension in the wire is 10 N,…

A:

Q: Assume Young's modulus for bone is 1.50 x 1010 N/m2. The bone breaks if stress greater than o= 45844…

A: Young's modulus is Y= 1.5×10¹⁰  N/m²  Maximum stress is σ = 45844 N/m²  Effective radius of the bone…

Q: a)Calculate the bone shear force acting on the lumbar vertebra. Report the force in units of N…

A: The objective of the question is to calculate the bone shear force, bone compressive force, and back…

Q: elastic plastic, 0 0.002 0.004 0.006 0.008 Strain & (mm/mm) Why is there a common behavior between…

A: Why there is common behavior between plastic and elastic.

Q: Calculate the modulus of the force acting on a 7.25 kg block thrown at 45° which hits the ground at…

A: This is case of projectile motion. We first find the velocity at the time of release from the hand.…

Q: The 60-mm-diameter shaft is made of 6061-T6 aluminum having an allowable shear stress of Tallow=85…

A: Given that, The diameter of the shaft, d = 60 mmThe allowable shear stress on the shaft,…

Q: The graph below shows the tensile stress against strain for a glass fibre. stress/10°Pa 100 80 60 40…

A: (a) given graph is between tensile stress vs strain in glass fiber it's a straight line and slope of…

Q: r end of the steel rod an n the lower end of the ste 0.75 m

A: Given: ∑Mo=00.75Pst=PalPst=2Pal

Q: o is when a force causes compression and the object shrinks * O Inertia compressive stress, O…

A: Answer:-  tensile stress  Sigma is when a force causes compression and the object shrinks - tensile…

Q: Explain about Tensile and Compressive Stress and Strain.

A:

Q: QUESTION 18 The stress-strain graphs for materials A and B are shown below. The graphs are drawn to…

A: Given : Stress - Strain graphs for materials A and B

Q: Determine the maximum shear of the beam loaded as shown. 400kN 10kN/m 10m 10m 20m R1 R2

A:

Q: The 3 nails in the figure can withstand an average shear stress of 40 MPa. Determine the shear…

A: Write the given values with the suitable variables. τ=40 MPa=40×106 Par=4 mm=4×10-3 m Here, τ and r…

Q: In the linear region of the Strain vs. Stress diagram is called Elastic Modulus * True False

A:

Q: Question A circular shaft is subjected to a torque of 50 kN-m. If the permissible shear stress is 4…

A: Given: A circular shaft subjected to a torque, T=50 kN-m Permissible shear stress, τ=40 MPa

Q: The stress-strain graphs for materials X and Y are shown. Strain Strain graphs are drawn to the same…

A: ( a ) Comparing the two graphs we can infer that the stress on X is greater than that on Y for the…