Folowing data refer to a rope-brake dynamometer: Radjus or the brake drum-125 cm, Diameter of rope 25 mm, Dead load in pan- 2451.7 N, Sering balance reading= 392.3 N, and r.p.m.- 125. Find the B.H.P and LH.P. of the engine if mechanical efficiency is 80%.

Folowing data refer to a rope-brake dynamometer: Radjus or the brake drum-125 cm, Diameter of rope 25 mm, Dead load in pan- 2451.7 N, Sering balance reading= 392.3 N, and r.p.m.- 125. Find the B.H.P and LH.P. of the engine if mechanical efficiency is 80%.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q7 An engine cylinder has a compression ratio (r) of 7.5, a clearance volume of 35 cm³ and a piston stroke length of 325 mm. What is the bore diameter in millimetres (mm) for the engine cylinder to the nearest mm.
An engine cylinder has a compression ratio (r) of 7.5, a clearance volume of 35 cm3 and a piston stroke length of 325 mm. What is the bore diameter in millimetres (mm) for the engine cylinder to the nearest mm.
Please solve the Below problem using 'Design data book'. And while solving problem add some table or figure reference number before taking each reference value. If answer is right then I will give you upvote/like.
A ball bearing subjected to a radial load of 4000 N is expected to have a satisfactory life of 12 000 hours at 720 r.p.m. with a reliability of 95%. Calculate the dynamic load carrying capacity of the bearing, so that it can be selected from manufacturer's catalogue based on 90% reliability. If there are four such bearings each with a reliability of 95% in a system, what is the reliability of the complete system?
5) Which statement is true about the friction factor in the Moody diagram (shown below). Moody Diagram 0.1 0.09 Transition Region 0.08 0.07 0.05 0.04 0,06 0.03 0.05 0.02 0.04 0.015 0.01 0.03 0.005 0.002 0.001 5x10-4 2x10-49 10-4 5x10-5 10-5 5x10-6 10-6 Friction Factor 12---- Laminar Flow 64 Material Concrete, coarse 0.25 0.025 Concrete, new smooth Drawn tubing 0.0025 Glass, Plastic Perspex 0.0025 Iron, cast 0.15 Sevens, old 3.0 0.1 Steel, mortar lined Steel, rusted 0.5 Stoel, structural or forgod 0.025 Water mains, old Friction Factor=AP. 1.0 Smooth Pipe 3000 10³ 10¹ 105 106 107 108 Reynolds Number, Re - Vd P a) The lines for different relative roughness in the turbulent regime correspond to Darcy-Weisbach model b) The lines for different relative roughness in the turbulent regime correspond to Nikuradse model c) The lines for different relative roughness in the turbulent regime correspond to Hazen-Williams model d) The lines for different relative roughness in the turbulent regime…
B7
1. A six-cylinder two-stroke engine with a compression ratio = 9 produces a torque of 1100 Nm at a speed of 2100 rpm. It has a bore bof 123 mm and a stroke s of 127 mm. (a) What is the displacement volume and the clearance volume of a cylinder? (b) What is the engine bmep, brake power, and mean piston speed?
A ball bearing subjected to a radial load of 4000 N is expected to have a satisfactory life of 12 000 hours at 720 r.p.m. with a reliability of 95%. Calculate the dynamic load carrying capacity of the bearing, so that it can be selected from manufacturer's catalogue based on 90% reliability. If there are four such bearings each with a reliability of 95% in a system, what is the reliability of the complete system?
You want to put larger tires on your truck. The manufacturer tires are P265/65R18. You want to upgrade to P285/75R19. Complete the information below for each tire size. Please upload a picture//file of your work.
An engine of 175 mm bore and 375 mm stroke is governed by hit and miss type governor to 220 rpm. With a fixed setting of the gas supply and ignition advance, indicator diagrams gave the following values of mean effective pressure. Firing, positive loop 5.7 bar, negative loop 0.25 bar; missing negative loop 0.42 bar. When developing 6 kW the explosions were 100 per minute and the gas used was 0.1 m per minute. Calculate the friction power and assuming uniform gas supply per explosion, find the gas consumption per minute at no load.
A rope-brake dynamometer attached to the crank shaft of an IC engine measures a brake power of 10 kW when the speed of rotation of the shaft is 400 rad/s The shaft torque (in Nm) sensed by the dynamometer is....
solve part (iv)