Following are the data of gauge and discharge collected at a particular section of the river by stream gauging operation. Gauge Discharge reading (m) (cms) 9.5625 15 9.625 30 9.7125 57 9.75 39 9.875 60 9.8875 100 10.1 150 10.6 170 11.225 400 11.625 600 11.875 800 13.125 1500 13.875 2000 14.625 2400 1. Develop a rating curve for this stream at this section for use in estimating the discharge for a known gauge reading and fit a linear regression equation for use in estimation of stage for a known value of discharge. Use a value of 9.375 as the gauge reading corresponding to zero discharge. 2. What is the coefficient of determination (R-) of the derived relationship? 3. Determine the stage for a discharge of 3500 cms. 4. Determine the discharge for a stage of 25 m.

Q: How to Install the Gypsm Board.

A: Gypsum Board: Gypsum boards or Plasterboards are one of the latest trends in the construction…

Q: what is the size of a standard exterior and interior doors with flames

A: standard doors are the doors of a specific size that we encounter in our day today life  there are…

Q: - consider the place acoustically ufficient, what kind of materials in hich shapes should be used,…

A: Instructions to Design A Conference Room For The Modern Office There's a ton to think about when…

Q: what is piping system?

A:

Q: QUESTION 2 120 8 22- 14 - 40 70 56 34 44 R8 024 e 12 O8-2 Holes 64 26 34 22- STEPS: 56 1) Draw the…

A: For given isometric view, we identify the direction of the view. after identify that we can able to…

Q: Define stirrup

A: Stirrup: A stirrup is a closed loop of reinforcement(steel bar) in a beam. It is called as tie-bar…

Q: How are forces between the tape and strips similar to those of magnetism?

A: The forces between a strip of adhesive tape and a surface are primarily due to intermolecular forces…

Q: For what reason must wires and plumbing fixtures installed above drop ceilings be plenum-rated?

A: Cables are distinguished as plenum and non-plenum based on the outer covering's (jacket) fire…

Q: use the parametric cost estimate method to estimate the plumbing cost of this building plan:

A:

Q: an 80 feet flagpole upper and lower diameter of 4 and 16 inches. find the cost of painting if at 10…

A: Given: The height of the flagpole is 80 ft. The upper diameter is 4 in. The lower diameter is 16 in.…

Q: *On the drawing attached, apply a runout requirement to make the left face perpendicular to the…

A: Introduction- Whenever the target is rotating once on the reference axis line, the run-out of the…

Q: one help please can you help me to draw an isometric view of the bridge (truss)

A:

Q: Write short notes on the following topic with proper figure. (6) i. Wrinkling ii. flattening iii.…

A: BASIC DESCRIPTION:  Mandrel tube bending, using a mandrel…

Q: How do you think are the details for cut bars and anchorages determined? Answer in 3-4 sentences…

A: Anchorage: The reinforcement bars are provided in the type of hooks and bends. The anchorage bars…

Q: Problem 1 Wind blows on the side of a fully enclosed agricultural building located on an open flat…

A: When wind engineering is used to analyse tall buildings, the major load is frequently found to be…

Q: What are canopy restrictions?

A: Canopy:

Q: L-16 W-4"

A: Board feet= (thickness*width*length*number of pieces) /12 = (2*4*16*24) /12 =256bf

Q: Find a more requesting section of the bars below. (do the calculations and diagrams of the options)

A:

Q: 4225- CAR FORCH 4225- -5150- FORCH 0.00 000 DINING ARA 00000 ENRY PORCH -5150- 15150- 1550-18002425…

A: To Identify and circle 1 Simply Supported Beam and 1 continuous Beam at the structural drawing given…

Q: How does a plumbing contractor know what slope is required on sanitary piping installations?

A: The slope changes as the temperature changes in a sanitary installation.

Q: What are high-performance lighting design options?

A: High-performance lighting refers to lighting systems that are designed to maximize energy efficiency…

Q: y thermal bridging? thank you if you will answ

A: A thermal bridge, also known as a cold bridge, is a section of a building with much higher heat…

Q: SFCA Given: 975 LF of 3 4" base molding. Calculate painting quantity in square feet.

A: Length of molding = 975 linear foot Dimension of molding = 3.25"

Q: ments Collaborate 此片 Freak Out Slice Crop Horizontal Start New Sheet Sketch Sketch Sheets 5 LBS…

A:

Q: What are flame-spread classifications?

A: Flame - spread: Flame spread is essentially a material's surface burning trait, and a flame-spread…

Q: What is the use of a magnetic needle?

A: Magnetic needle The magnetic needle is used in compasses that are magnetic in nature.

Q: "-Q3.33-. A cantilever beam as shown in the figure has a clear covering of 50 mm at the top and at…

A:

Q: Given the multiview projection of the solid, draw the isometric view.

A: Projection: - It is defined as image or figure of an object on a plane which is formed by joining in…

Q: Why compass box is covered with glass?

A: compass box is a box which contains magnetic needle.  A needle is pivoted inside the box which can…

Q: What are the common types of lighting systems?

A: There are different types of lighting systems Incandescent light bulbs Fluorescent lamps. High…

Q: If 2x8 wall studs were requested to be installed for a 90' long wall, what would be the number of…

A: Given data: Length of the wall = 90' = 12 x 90 =1080" Spacing = 24"

Q: Define Vibrocompaction.

A: Vibrocompaction is a method in which the density of granular soils is increased to the appropriate…

Q: Non-Homogeneous LDECC Solve the following and box your final answer. Please answer it in detailed…

A:

Q: s inciudes primary, secondary and worKing control on the jobsite. Referencing Control Vertical…

A: Referencing controls the primary secondary and working control on jobsite

Q: What are servomotors?

A: Servomotors are used in cars to control its speed.

Q: give detailed information about generalised compressibility chart.

A: It has been asked in the question to give detailed information about generalized compressibility…

Q: From this plan view,which one is the length and which one is the width and please justify your…

A: The length shows the longer side of the figure, while the width shows how broad or wide it is.…

Q: Arch 486 Detail Problem: 2023 Detail Problem Draw a pinned connection and a fixed connection for…

A: Fixed Connection: For a 2 dimensional structure, fixed connection has three reaction forces. They…

Q: If the resultant of the loads shown passes through point B, determine the equivalent force-couple…

A: For resultant of the load to pass through point B. Reaction force at A (RA) = 0

Pricing Concrete Work

The concrete work in a project usually holds a high-end cost in terms of cost and value of the work. It becomes an important step in calculating the cost associated with concrete while preparing the project scale. The cost of making concrete depends on the cost of building materials, mixed materials, labor, and machinery. A concrete contractor builds structures from concrete, usually managing all the steps of the process from assembling ingredients to building a holding structure and preparing the mixture. This person or team oversees the delivery and unloading of goods to ensure that they are done properly. Nowadays, most of the concrete in the United States comes from manufacturers working abroad, usually with branches and plants within the provinces. Contributions can range from pre-mixed concrete to basic ingredients, the consumer company then mixes it. Many American-based concrete companies, however, offer concrete products, such as ballads, bricks, countertop, concrete pipe, and building products, as well as concrete construction and installation materials. This article covers both types of suppliers for this set of building materials.