Flow straighteners consist of arrays of narrow ducts placed in a flow to remove swirl and other transverse (secondary) velocities. One element can be idealised as a square box with thin sides as shown below. Calculate the pressure drop across a box with L=22 cm and a= 2.7 cm, if air with free-stream velocity of Uo = 11 m/s flows though the straightener. Use laminar flat-plate theory and take µ= 1.85 x 10-5 and p = 1.177kg/m3 . %3D Pa.s

Flow straighteners consist of arrays of narrow ducts placed in a flow to remove swirl and other transverse (secondary) velocities. One element can be idealised as a square box with thin sides as shown below. Calculate the pressure drop across a box with L=22 cm and a= 2.7 cm, if air with free-stream velocity of Uo = 11 m/s flows though the straightener. Use laminar flat-plate theory and take µ= 1.85 x 10-5 and p = 1.177kg/m3 . %3D Pa.s

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A water jet 3 in in diameter strikes a concrete (SG =2.3)slab which rests freely on a level fl oor. If the slab is 1 ft wide into the paper, calculate the jet velocity which willjust begin to tip the slab over.
When an oblique shock strikes a solid wall, it reflects as ashock of sufficient strength to cause the exit flow Ma3 to beparallel to the wall, as in Fig. For airflow with Ma1 =2.5 and p1 = 100 kPa, compute Ma3, p3, and the angle ϕ.
I need right solution with clear calculations.
Airstream flows in a converging duct from a cross-sectional area A1=50cm2to across-sectional area A2=40cm2. If T1=300K, P1=100kPa, and V1=100m/s, find M2, P2,and T2.
Please also explain.
Problem-2 For the turbulent incompressible boundary layer, the velocity profile is given as u/Ue, y = y/8, Ue and d are boundary-layer edge velocity where, u = and boundary layer thickness, respectively. Using momentum integral equation, prove that: 8/x = 0.383/Re,/5 8% /x = 0.0479/Re/5 and 0/x = 0.0372/Re/5
In the flow of air at 20°C and 1 atm past a flat plate inFig. , the wall shear is to be determined at position x bya floating element (a small area connected to a strain-gageforce measurement). At x = 2 m, the element indicates ashear stress of 2.1 Pa. Assuming turbulent flow from the leadingedge, estimate (a) the stream velocity U, (b) the boundarylayer thickness δ at the element, and (c) the boundary layervelocity u, in m/s, at 5 mm above the element.
answer quickly
Show work for both subparts as it is a single problem.
The wing of a tactical support aircraft is approximately rectangular with a wingspan (the length perpendicular to the flow direction) of 16.5 m and a chord (the length parallel to the flow direction) of 2.75 m. The airplane is flying at standard sea level with a velocity of 250 ms¯¹. Assume the wing is approximated by a flat plate. Assume incompressible flow. Use μ = 1.789 x 10-5 kg/ms (a) If the flow is considered to be completely laminar, calculate the boundary layer thickness at the trailing edge and the total skin friction drag.
Air flows past a two-dimensional wedge-nosed body as inFig. . Determine the wedge half-angle δ for whichthe horizontal component of the total pressure force on thenose is 35 kN/m of depth into the paper.