Flow enters the rotor of an LP axial flow compressor with an absolute velocity of 150m/s purely in the axial direction. The LP shaft rotates at 8600rpm and the compressor is designed to have a constant axial velocity throughout. The angle of the relative velocity at exit of the rotor is 30 degrees to the axial direction.

Flow enters the rotor of an LP axial flow compressor with an absolute velocity of 150m/s purely in the axial direction. The LP shaft rotates at 8600rpm and the compressor is designed to have a constant axial velocity throughout. The angle of the relative velocity at exit of the rotor is 30 degrees to the axial direction.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Wind provides an increasingly important source of renewable energy in certain locations of the world. In fact, wind was the second largest renewable energy source worldwide (after hydropower!) and provided more than six percent of global electricity in 2020; in the U.S. that number was 8.4%. Suppose that wind turbines can convert up to 30% of the kinetic energy of incoming wind blowing through their blades into electricity (i.e., useful shaft work). In the following, we will analyze the power output of a wind turbine with a diameter of d 80 m placed at an offshore location where the wind blows steadily at an average speed of 20 knots. Explicitly state all relevant approximations or assumptions. = (a) Draw a diagram that includes appropriate elements for assessing the amount of work extracted from the wind turbine. Your diagram should have annotated any known or approximated proper- ties. What is your system and surroundings? What kind of boundary divides these two? Hint: In terms of…
!
Steam flows steadily through an adiabatic turbine. (CC)) BY-NO-SA Niel Crews, 2013 The inlet conditions of the steam are: pressure = 9 MPa temperature = 450 °C velocity = 80 m/s The exit conditions are: pressure = 10 kPa quality= 0.91 velocity = 50 m/s a) What is the temperature of the fluid at the turbine exit? b) What is the power output of the turbine, per unit mass of the working fluid? kJ kg
do fast ...need explanation
As we learned, Bernoulli's equation is not to be used in many situations. Let's say you are examining changes between two points in a flow. Which ONE of these scenarios could you appropriately use Bernoulli's equation on? O A turbine is situated between the two points There are large changes in kinetic energy between the two points The mass flow rate between the two points changes with time There are large changes in density between the two points There are large viscous losses between the two points QUESTION 10 A 12 cm diameter jet of air strikes a plate positioned normal to the flow, with all air deflected away parallel to the plate. If the air flows at a speed of 20 m/s, what is the force needed to held the plate in place? Do not use a linear momentum correction factor. O 0.272 N 10.9 N 4510 N 5.45 N 0.340 N
solve the following question and show the complete solutions
In a double-acting cylinder, whose piston and stem diameters are 150 mm and 80 mm, respectively, a flow rate of 50 l/min acts, both in the advance and in the reverse. It is requested: A) Calculate the speed of advance. B) Calculate the return velocity. C) State the continuity equation for a liquid with stationary flow.
You have a wind turbine with a maximum power rating of 5 MW available for use in a wind farm. This turbine can operate in winds ranging from a minimum speed of 2 m/s up to a maximum wind speed of 10 m/s (which is when the turbine produces its maximum power). You have two possible sites available: the first site has a steady wind that always blows at 6 m/s. At the second site, the wind blows at 1 m/s for 50% of the time, and at 10 m/s for the other 50% of the time. a. If maximizing the peak power production is the most important consideration, which site should you choose? What will be the maximum power for a single turbine? b. If maximizing the average power production is the most important consideration, which site should you choose? What would be this average power for a single turbine?
subject (fluid mech 2) pls show me full steps sir with clear handwriting pls answer me withi 30 min sir