Find the sum of two sinusoidal voltages, given as follows: V₁ (t)=V1 cos(wt+$₁) and V2 (t)=V2 cos(wt+2). You are told that V1 = 15, V2 = 16, w = 1,000, ₁ = 72° and $₂ = 44°. Hint: we recommend using the phasor transform to add these signals in the frequency domain. Once you have added the signals, please enter the angle (in degrees) below. Enter the answer to 3 significant figures.

Find the sum of two sinusoidal voltages, given as follows: V₁ (t)=V1 cos(wt+$₁) and V2 (t)=V2 cos(wt+2). You are told that V1 = 15, V2 = 16, w = 1,000, ₁ = 72° and $₂ = 44°. Hint: we recommend using the phasor transform to add these signals in the frequency domain. Once you have added the signals, please enter the angle (in degrees) below. Enter the answer to 3 significant figures.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A certain RLC series circuit has an AC signal applied to it. Under which of the following circumstances will the total impedance of this circuit be lowest? a) When the frequency of the AC signal is arbitrarily large b) When the frequency of the AC signal is approximately zero c) When the frequency of the AC signal is such that the capacitive reactance matches the inductive reactance
In the circuit, v₁ and ₂ are AC sources with = 100 rad/s. The phasor diagram shows the phasors of v₁ and v₂. It is not drawn to scale. You may assume the system is in steady state. V3 is a DC source. (a) What is v₂ where I is the period of the waveform ? (b) What is the waveform ia(t)? (c) What is the maximum value of the waveform va(t)? V3 L + V1 1 + + Va V2 V₂ a Im V₁ να Re |V1|: |V2|: alpha: V3: C: L: 2 V 3 V 30 degrees 3 V 10 mF 25 mH
1. Suppose that MATLAB is used to plot a sinusoidal signal. The following MATLAB code generates the signal and makes the plot. Draw a sketch of the plot that will be done by MATLAB. Determine the amplitude (A), phase ($), and period of the sinusoid and label the period on your plot. dt = 0.001; tt = = .05 dt : .15; Fo = 8; Z sqrt (2) * (1-j); xx = real( Z*exp( 2j*pi*Fo*tt ) ); plot tt, XX ), grid title( 'SECTION of a SINUSOID' ), xlabel('TIME (sec)')
A typical AC signal is the sinusoidal signal, and a general mathematical expression of a sinusoidal signal is: A cos(w.t+), where A is the amplitude, w is the frequency, t is time, is phase angle. For instance, the output voltage of an AC voltage source can be represent as: Vs (t) = 10 cos(2. t + 60°). To analyze AC circuits, we convert AC signals from the time domain to the frequency domain. Phasor is the resulting frequency domain representation: A cos(w t+) A. ejo On the left side is a sinusoidal signal, and on the right side is a Phasor. j is complex number notation, where j² = -1. To get a Phasor notation from a time domain signal, we take the amplitude and the phase angle information from the sinusoidal signal. To convert a Phasor back to a sinusoidal signal, you need to know the source frequency. Which is the correct Phasor representation for V₂ (t) = 10 cos(2 t + 60°)? 10. .e2 O 10. e60° 02.2 2. e360°
Represent the following waveforms by using the ramp r(t) and unit step u(t) functions.
2. Express the following functions as a cosine: a. 10 sin(wt +30°) b. -40 sin(wt - 70°) c. 25 sin(wt 15°) d. 5 sin(wt +230°) - 3. For the two signals Va(t) and Va(t) below, draw the phasor diagram for both signals, then determine which one leads and by how much: Va(t) = 12 cos(4t-80°) Volts Vb (t) = 10 sin(4t + 20°) Volts complex numbers, express the results in polar form. 4. Evaluate the following a. 3 + 4j b. -11j c. -12 + 15j d. 5 - 4j 5. Find the phasors corresponding to each of the following signals: a. v(t) = 12 cos (4t- 200°) Volts b. i(t) = -50 sin(100t +30°) Amps c. i(t) = -45 cos(6t+ 40°) Amps d. v(t) = 8 sin (200t - 170°) Volts
K:21)
An 50 resistor, a 5 mH inductor, and a 1.25 μF capacitor are connected in series. The series-connected elements are energized by a sinusoidal voltage source whose voltage is 600 cos(8000t+20°) V. Part A Determine the impedances of the elements in the frequency-domain equivalent circuit. Express your answers in ohms to three significant figures separated by commas. Enter your answers in rectangular form. IVE ΑΣΦ ZL. ZC, ZR= 40,100,50 vec You have already submitted this answer. Enter a new answer. No credit lost. Try again. Submit Previous Answers Request Answer ? Ω
Write the equation for this sinusoid in the time and phasor domain
The second photo is a solution from bartleby expert but they never gave any plot sketches! Can you help me plot the graphs?
A 60microHenry inductance is connected across a given supply voltage. Find the La Place transform of its voltage.
Find the rms value of the periodic function described in figure below. Assume that Vi= 2 mV, V2= 4 mV, V3= 6 mV, and va= 8 mV. v (V), V3 V2 TO T5 20 25 30 35 40 45 I (ms) - V2 - V3 V4 1 cycle www