Find the strain of a brass rod of length 250mm which is subjected to a tensile load of 50kN when the extension of rod is equal to 0.3mm* 0.025 0.0012 0.0046 0.0014
Q: our biceps muscle is attached to your elbow by the distal biceps tendon. An average adults tendon…
A:
Q: A steel cube of side length L = 0.5 m is subjected to a shearing force of 5000N along the top…
A:
Q: A strand of dragline spider silk has a diameter of 6.0 μm, and can support a mass of 2.9 g.…
A: Required : Approximately how many copper wires would it take tosupport the same mass?
Q: A cylindrical steel wire that is 2 m long must stretch no more than 0.25 cm when the applied tensile…
A: The objective of this question is to find the minimum cross-sectional radius of a cylindrical steel…
Q: If the elastic limit of copper is 1.50 x 108 N/m2, determine the minimum diameter a copper wire can…
A: Given- If the elastic limit of copper is 1.50 x 108 N/m2, determine the minimum diameter a copper…
Q: A steel bar is stresses to 250 MPa. The modulus of elasticity is 250 GPa. The bar is 80 mm diameter…
A:
Q: A 2 m long steel rod has a cross-sectional area of 0.3 cm?. The rod is a part of a vertical support…
A: The stress of the rod is given by F/A Strain is given by dL/L where F= Force…
Q: The maximum compressional stress that a bone can withstand is 1.6 × 108 N/m2 before it breaks. A…
A:
Q: A tendon is subjected to tensile forces. The cross-sectional area of the tendon is 0.0002 m2. If the…
A: See below
Q: A structural steel bar with a 3.6 in. x 0.890 in. rectangular cross section is subjected to a…
A:
Q: A marble column with a cross-sectional area of (2.70x10^1) cm² supports a load of (5.500x10^4) N.…
A:
Q: A solid copper cube has an edge length of 89.9 cm. How much stress must be applied to the cube to…
A: The ratio of volumetric stress with volumetric strain is defined as the bulk modulus. To solve the…
Q: A 92.0-kg man’s thighbone has a relaxed length of 0.789 m, a cross-sectional area of 7.00 × 10−4 m2,…
A: The objective of the question is to find out how much the thighbone of a 92.0-kg man compresses when…
Q: The figure shows the stress-strain curve for a material. The scale of the stress axis is set by…
A: Given : scale of the stress axis is set as s=320 in a unit of 106N/m2 ε=0.0090
Q: The free body diagram must be included. Mechanics of materials (mechanical engineering) Stop using…
A: Step 1:Step 2: Step 3: Step 4:
Q: A solid copper cube has an edge length of 88.9 cm. How much stress must be applied to the cube to…
A:
Q: Humans can bite with a force of approximately 795 N. If a human tooth has the Young's modulus of…
A: Young's modulus is defined as the ability of a material to withstand the change in length due to…
Step by step
Solved in 2 steps
- Assume a person's mass is 62.0 kg and each of her shoes has an area of 220 cm2. F What is the compressive stress on her feet if her weight is A F spread out evenly over both soles of her shoes? 13.82 Ра A By what factor f does the compressive stress change if only 10.0 cm? of each shoe is in contact with the floor (as might be f = the case for high-heeled shoes)? * TOOLS x10A solid copper cube has an edge length of 89.1 cm. How much stress must be applied to the cube to reduce the edge length to 89 cm? The bulk modulus of copper is 1.4 x 10¹¹ N/m². Number i UnitsA 1.0 x 10-3 kg spider is hanging vertically by a thread that has a Young’s modulus of 4.5 x 109 N/m 2. What is the cross-sectional area of the thread when strained (strain = 0.1) by the full weight of the spider?
- A 1.25 m long cable has a diameter 3.50 mm with a Young’s Modulus, E, of 9.75 x 109 N/m2 . When the wire is placed under tension, it experiences a stress of 202.52 x 106 N/m2 , the length of the cable extends by 36.35 mm. Calculate the force that the cable experiences under tension and the strain energy density (U/V) due to deformation. Give your answers in newtons (N) to 2 decimal places for the force; and in joules per cubic metre (J/m3 ) for the strain energy density to 2 decimal places. Assume the cable is solid and the material is homogeneous.A structural steel bar with a 3.6 in. x 0.890 in. rectangular cross section is subjected to a tensile axial load of 54 kips. Determine the maximum normal and shear stresses in the bar. Answer: Omax i ! ksi %3D Tmax = i ksi