Find the steady-state current in the RLC-circuit in Fig. 61 for the given data. Show the details of your work. R = 40, L = 0.5 H, C = 0.1 F, E = 500 sin 21 V Eu) -E, sin eat Fig, 61. RLC-circuit

Q: Review V: 120 coS Li000) R- 6R RLC circuits L = 2 mH C: 5000 uF W= 1000 : 21€ Find I V: Vmax cos…

A:

Q: Don't use chat gpt It

A:

Q: The function for a current is /(t) = 9cos 120nt where / is the current, in amperes, and t is the…

A:

Q: As shown below, a wire loop is immersed in a 0.8 T B-field (the direction of the field is shown in…

A:

Q: Find the steady-state current q (t) on the capacitor and the current i (t) in the given LRC-series…

A: The equation for the given LRC circuit is,…

Q: The voltage source in the Figure has an output of A Vrms = 85 V at an angular frequency of w = 1100…

A: Write the expression for the impedance and substitute the required values.

Q: 1. Set up a slide-wire Wheatstone bridge circuit as in Fig. 1 a, using the previous small known…

A: Let's draw a Wheatstone bridge circuit in this regard to understand easily. In the balanced…

Q: For the op-amp circuit shown below. Find the values of R & R, such that the output to be V=-5V +3V.…

A: The given OpAmp. Circuit is a Difference amplifier. It gives us the desired difference in input of…

Q: 6. An RLC circuit has R = 5.00 N, C = 20.0 µF, L = 1.00 H, and V, = 30.0 V. %3D a) At what angular…

A: Given : R=5 ohm C=20x10-6 f L=1 H V=30 V

Q: HO09 1.75x 10°F

A:

Q: Problem 9.5 Use the value of the inductance and capacitance of a pair of plane parallel conductors…

A: Given, Characteristic impedance of waveguide.

Q: What is the phase constant for the resistor (ϕR)?

A: The phasor diagram for the given RLC circuit is shown below:

Q: Find the charge on the capacitor in an LRC-series circuit at t0.03s (find the charge g(t) and then…

A: The charge on the capacitor is 3.4118 C

Q: CURRENT DECREASING TO ZERO: Previously we found the current immediately after a circuit is changed…

A:

Voltage Across Inductor

An actor is a passive electrical component that consists of a coil bent in the form of wire which uses electromagnetism to produce electric current through the coil. When the electric current flows through a conductor that is the coil, a magnetic flux is developed around the conductor. This flow of current through the coil creates a magnetic field based on Fleming's Right-hand thumb rule. If there is any decrease in the current passing through the inductor, then the magnetic field will also decrease and energy is released through the generation of electric current. There is also a secondary voltage inducing in the same coil due to the magnetic flux, since it opposes any changes in the electric current flowing through the circuit. An inductor is also called choke, coil, or solenoid. A choke is designed to block certain frequencies when the DC current passes. A winding coil is coated with insulation to give extra insulation and protect the circuit. They are usually tightly wrapped around a central core which is cylindrical in nature so that the magnetic flux can be induced. The solenoid is a three-dimension coil that is used to exhibit electromagnetism when the magnetic field is developed due to the current flowing through the coil. The sign convention of the inductor is the same as the power dissipating device. When the current flows into the positive side of the voltage across the inductor, the value is positive and the inductor dissipates power whereas when the inductor releases the power back to the circuit, the current has a negative sign convention.