Find the safe live load that the rectangular beam shown could carry if it is reinforced with 2 - 36 mm φ bars at the top and 5 - 36 mm φ bars placed at the bottom with an effective depth of 510 mm. Steel covering is 50 mm at the top, fc’ = 35 MPa, fy = 400 MPa. Span of beam is 6 m.

Q: 2) As shown is the partial plan of the corridor of a certain building. If live load is 4 KPa and…

A:

Q: A W6x12 beam is strengthened with a % x ¾ inch bar welded to its top of the top flange on…

A: For W 6 x 12. D(depth) = 12" , Bf (width of flange)= 4", tw (web thickness) = 0.23", tf (flange…

Q: Situation #2: A properties: Width, b = 400 mm 415 MPa rectangular beam has the following Effective…

A:

Q: steel beam of I cross-section is simply supported on a span of 4m. Find the safe uniformly…

A: Given:- Span = 4m Simple Supported beam Tensile stress = 35N/mm2  To find:- w, δmax compressive

Q: Given: Consider the floor frame below supports a 6-in. concrete floor. Assume the beams and girders…

A:

Q: Two designs for a beam are to be considered. Determine which one will support the loading shown…

A:

Q: "D.77. Compute the ultimate strength capacity of the positive moment beam design below. f'c= 21 MPa,…

A:

Q: O . A

A: Which of the following is symmetric beam? option (b) is correct option

Q: The beam shown carries an ultimate load of 28.5 kN/m. The beam has a limited width of 275 mm and…

A: Ultimate load = 28.5 kN/m Width, b = 275 mm Height, h = 450 mm Reinforcement is placed at 65 mm from…

Q: the rectangular beam given in figure below has been designed for flexure; design the necessary shear…

A: It is required to determine the factored load. wu=1.2DL+1.6LL=1.240+1.625=88 kNm It is required to…

Q: Determine the maximum uniform load w that the beam can carry using A-36 steel. The lateral supports…

A:

Q: ion is an ith the greater width width at the bottom. am is 300 mm, and op and the bottom of and 50…

A:

Q: A steel beam of I cross-section is simply supported on a span of 4m. Find the safe uniformly…

A: Consider the free body diagram;

Q: a) If olow 160 MPa, select the most economical metric wide- flange shape that should be used to…

A: Data given: σallow = 160 MPa Asked: Select most economical metric-wide flange shape Calculate Von…

Q: A W610 x 82 beam of A 36 steel has end reaction of 302 kN and is supported on a plate with a length…

A: Yield Strength :Yield strength of an element is a maximum stress an element or component can bear…

Q: Calculate the development length at simply supported edge in mm from the following information: M25…

A: Side way clear spacing is 50 mm,M25 and Fe 415 steelbd =1.4 MPaV = 30 KN and M = 16.076 KN-md = 120…

Q: a. Nominal moment capacity of the overhanging portion of the section. b. Depth of the compression…

A: Solution: Givendata: bf = 750 mm tf = 50 mm d = 750 mm bw = 350 mm Mu = 816 kN.m fc' = 20.7 Mpa fy =…

Q: A rigid bar is supported by three non-rigid rods, as shown. There is no initial strain and the…

A:

Q: Steel Design Two channels having the given properties shown is placed at a distance of 300 mm to…

A: Compression members are structural elements primarily subjected to axial compressive forces and…

Q: 0:Design the steel reimforcement for flexural for the beam shown m the kN fig.below The dead load on…

A: if the size of beam is known and area of reinforcement is need to design then their is 2 cases  1-…

Q: Quiz: Design the reinforcement steel that necessary for the shear and torsion for the rectangular…

A: Solution; Given that; Live load=10 KN/m2Dead load =5 KN/m2fck=26MPafy=400 MPa

Q: The building shown in Figure 1 is subjected to an unfactored dead load of 45 psf and an unfactored…

A: DL = 45 lb/ft2LL = 65 lb/ft2 Slab dimension:Longer length, Ly = 30 ftShorter span, Lx = 22 ft, 15…

Q: A cantilever beam AB of length L = 6.5 ft supportsa trapezoidal distributed load of peak intensity…

A: Given:- L=6.5ft  σallow =18 ksi τallow = 7.5 ksi To find:-  the maximum permissible load q based…

Q: Design the flexural reinforcement of the cantilever beam shown below for the given loading and data.…

A: Solution: Design Bending Moment and Shear Force: Design Load = 1.2DL+1.6 LL=1.2(100)+1.6(70)=232kN…

Q: A WT305 x 41 standard steel shape is used to support the loads shown. Assume w = 56 kN/m, LAB = 1.0…

A: To Determine Maximum Compressive and tensile bending stress.

Q: Rigid beam AB is supported by three bolts at A and a pin at B. The bolts at A are in double shear…

A:

Q: I cross-section is simply supported on a span of 4m. Find the safe uniformly distributed load the…

A: Draw the schematic diagram

Q: Check the adequacy of the isolated T-beam shown below according to ACI Code requirements and…

A:

Q: Find the moment of resistance of the section. The permissible stresses are 10 N/mm2 in tension and…

A: The values and diagram given in the question are as follows: The permissible stress in…

Q: A horizontal tension member is to be constructed of two pieces of plastic glued along the incline pq…

A:

Q: A WT305 x 41 standard steel shape is used to support the loads shown. Assume w = 52 kN/m, LAB = 2.0…

A:

Design criteria for structural loading

The different loads such as loads due to self-weight (dead load) and external loads such as live load, wind loads, seismic load, snow load, and other loads and load combinations that influence the design of a building are called structural loading. The nature of the applied load differs from changes in the location, design, and type of materials used. The design criteria require that structures must be designed and constructed to be able to withstand all load types that are expected to act upon the structure and render its usage for the designated purpose. The structural members such as beams, slabs, columns, and foundations help the structure to withstand the applied load. There are different institutes such as ASCE and ACI that provide building design codes to assure minimum safety requirements and quality of the structures.