Find the resultant force of the system of forces. Determine the moment about point O of each force acting on the pipe assembly. Find the resultant momer in term of the cartesian components. Calculate the magnitude and coordinate direction angles of the resultant moment. What would be an equivalent system of forces at F = (30i + 20j – 30k} N F2 = (60i – 10j - 35k} N A point "O"? 0.4 m 1.20 m

Q: Given the equation of the circle x + y? - 2x - 4y+1 = 0, find the centre of this circle. A. (-1,2)…

A: Given Data- The equation of the circle isx2+y2-2x-4y+1=0.

Q: 2. Determine the angle e between pipe segments BA and BC.

A:

Q: If b = 10 in, h = 5 in, X1= 5 in, and Y1=2 in, determine the magnitude of dy that would be used in…

A: given-         b=10in, h=5in X1=5in Y1=2infind- dy

Q: Replace the two pairs, demonstrated by a single equivalent pair

A: Consider the diagram shown for the given structure,

Q: Determine the (f_R, By using Law of cosine when ( A=8 lb, B=6 lb, c = 100°) .A 10 .B 11lb .C 10.8lb…

A:

Q: Member AB is supported by a cable BC and at A by a square rod which fits loosely through the square…

A:

Q: In a crossed-belt drive, two sheaves have diameters of 10 in and 12in. If the center distance is…

A: Given data, Centre  distance, x= 14 in.  d1= 10 in. d2= 12 in. It is cross belt.

Q: Find forces A and B in diagram at right.

A:

Q: What would be the resultant force F of the triangular distributed load and its location d measured…

A: Triangular load is also termed as uniformly distributed load.  The magnitude of the triangular…

Q: Determine the (f_y) when distance of y = 6.7 mm and the scale of force 30.55 lb/mm

A: Given:distance, y=6.7 mmScale of force, S=30.55 lb/mm

Q: 3. In the figure shown, solve for the distance b. 36 kN 20 kN y 94 kN m 2 m 3 m 2 m

A: Given Data :

Q: The three forces are applied to the bracket. Determine the maximum value for the magnitude of force…

A:

Q: Both pulleys are foxed to the shaft and as the shaft turns with constant angular velocity, the power…

A: The angle θ=0

Q: L1=4 in , L2=3 in, L3=1.5 in , h1=5 in , h2=6 in , f=7 lb , p= 45 lb. determine the proper angle in…

A:

Q: نقطتان )2( Q2/ Determine the horizontal resultants about A knowing that point A is fixed support *…

A:

Q: 5. A person pulls on a rope with a force of 100 lbs as shown below. What is the moment about point A…

A:

Q: Choose the correct statement from the below a. Resultant force and Equilibrant force are Coplanar…

A:

Q: Find the Resultant force for the following system. 15 kN 35 20 kN 30 25 kN

A: Parallelogram law: This law is used for finding the resultant of two vectors acting at a point. If…

Q: Can you now find the vertical support reaction in support B.  Enter your answer in kN to two…

A:

Q: esultant force.

A: given:

Q: Part A Determine the moment of force F₂ about point A on the beam. O M2 600 ft-lb ( OM2 50 ft-lb (…

A:

Q: Determine the angle between the two ropes. 1 m 2 m 1'm 3 m B. -y •G 1 m 1m

A:

Q: QS. Find I, for the shaded area. R25

A:

Q: 3. The uniform L-shaped bar pivots freely at point P of the slider, which moves along the horizontal…

A: Let the total mass of the L-shaped bar be 'm'. The weight acting on the different points of the bar…

Q: 600 N 600 N 40 250 N 250 N

A: Given Couple moment = 500 Nm To find Magnitude of F

Q: A moment of 260 lb-in is required to start rotating the triangular plate about the edge AC. What is…

A: Given: To find: Least force applied at B

Q: If the diameter (d) of wheel is reduced in half times in size, Then the torque produced in the wheel…

A: If the diameter (d) of wheel is reduced to half times in size, Then the torque produced in the wheel…

Q: Determine the magnitude and direction of F; so that If the resultant of the three forces act on the…

A: As per our guidelines we are allowed to do 1st question in multiple question, kindly post 2nd…

Q: Consider the area shown in (Figure 1). Suppose that a=h=b= 160 mm. Figure < 1 of 1 - Part A Locate…

A:

Q: ( Determine the (f_R ) By using Law of cosine when ( A=8 Ib , B=6 Ib ,c = 100° .A 10 .B 11lb .c…

A:

Q: Determine the magnitude of the resultant R 600 N 400 N 60 O a 1000 N Ob 600 N O. 529 N Od. 400 N

A: As per given  Question  We have to find determine magnitude of

Q: Consider the pipe shown in (Figure 1). The forces F = 650 N, F = 700 N , and F3 = 700 N are paral…

A:

Q: 4. If the resultaut force of tHhe two tug boats required to Io is to be Munimum det the magnitude of…

A:

Q: Q2: Determine (Y). D2 Y Q /sec L (m) D1 D2 220 0.5 5 0.25 D2 Y D1 Hg-

A:

Q: The force F of magnitude 700 lb is shown in the figure. It is to be resolved into two components…

A:

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.