Consider the area shown in (Figure 1). Suppose that a=h=b= 160 mm. Figure < 1 of 1 - Part A Locate the centroid y of the area. Express your answer to three significant figures and include the appropriate units.

Q: A 3/4-in.-diameter hole is drilled in a piece of 1-in.-thick steel; the hole is then countersunk as…

A: The required volume of the given hole is obtained by rotating the area shown about the Y-axis.

Q: y

A:

Q: Q243 For the force system shown in figure C24); determine The magnitude and location of the…

A:

Q: (Determine the (f_y ) when force 80 Ib and angle 30° on the axis (X .A 40 .B 40lb .C 4lb .D 40N

A:

Q: Problem 6 You've been asked to design a stamping tool as shown. What are the internal forces at A…

A: FBD

Q: The hollow cylinder shown in Fig. P.14.22 is built-in at one end and carries a vertical load of 2 kN…

A: The bending moment due to force is - M=2×1 kNm=2000×1000 NmThe twisting moment due to force is -…

Q: What is the magnitude of the resultant force related to the following distributed load.

A:

Q: PO 8 in.

A: Redraw the following figure for the given question.

Q: 2. EVALUATE dx e

A: The indefinite integration is represented by ∫f(x)dx and the solution is F(x)+C, where F(x) is…

Q: If Ma- 68.5 kN-m and Mc- 56.0 kN-m, use the graphical method to construct the bending -moment…

A:

Q: h a 60° 60° --X

A: Let’s divide the shaded area into two parts. Section 1 is a triangle OAB and Section 2 is a circular…

Q: Solve for the mobility.

A:

Q: find Q ? L 7om dsolm Lsioum L. 2om f=0002

A: Velocity of flow at entry of 100 m pipe, v=2gh where, h=height of reservoir=8m Therefore velocity,…

Q: What is the magnitude of the resultant force related to the following distributed load. 15 kN/m 7…

A: Option D is correct.  Resultant of uniformly distributed load is 99 kN.

Q: nd the Zero member enlys 3 3. 3. D. 3. 3. 8m

A: given; find zero force member only

Q: In the picture, a weight pulls on a pulley (solid disk) of mass 0.5kg and a radius of 0.25m. The…

A:

Q: - х a = 6 in b = 0.7 in C = 2 in

A:

Q: H G 60 E D 7 kN 7 kN 9 kN 6m 6m 6m 6m

A:

Q: The lower half of the moulding box is O a. Raiser O b. Drag O . Runner O d. cope

A: Given data Lower half of the moulding box is

Q: Determine the position of the neutral axis of a curved bar subjected to flexure by a couple shown in…

A: The position of the neutral axis of a curved bar subjected to flexure by a pair must be…

Q: The landing gear system of a plane is made of an actuator AC and 2 rods CB and OAB. They are pin…

A:

Q: 3. Tubing used for air-conditioning installations is usually insulated at (a) the low-pressure side…

A: Tubing used for air conditioning installations is usually insulated at the low-pressure because the…

Q: 400 Ib 14' A 60° 450 Determine the Value of P

A: given data: let  RA=normal reaction force at ARB=normal reaction force at B AC=4' CD=14' DB=2'

Q: ths angle of the three forse acting on hook

A: given: determine the resultant and the angle of the three forces acting on hook?

Q: If the diameter (d) of wheel is reduced in half times in size, Then the torque produced in the wheel…

A: If the diameter (d) of wheel is reduced to half times in size, Then the torque produced in the wheel…

Q: 1. If the block is loaded with P = 282 kN, calculate the required dimension "b" of the key.   Write…

A:

Q: What is θ3

A: Given, AD=10 cmAB=4 cmBC=7 cmCD=6 cmθ2=900

Q: 1. Determine the cylinder displacement and engine displacement of an engine having six cylinders…

A: given data  bore diameter = 102 mm = 0.102m stroke length  = 120mm =0.120m number of cylinders =6…

Q: Horizontal Component of the force at B: Vertical Component of the force at B: Horizontal Component…

A:

Q: Fint total force acting on point A. Point A can be anywhere.

A:

Q: QUESTION 2 A shaft rotates at 300 rpm. 1), If it carries a spur gear that delivers 5 hp to a mating…

A: Given: N=300 rpm

Q: Find (Ix&ly), if a=30mm. a

A:

Q: A) Resolve the 500-lb of fig. into two components: a shearing component parallel to AB and a normal…

A:

Center of Gravity and Centroid

The term center of gravity indicates the position or location of a point about which the whole weight of a body or system is supposed to be concentrated, which means the whole weight of the body or system works through this point. It is closely related to mass distribution. For all positions of the body, the center of gravity would be a single point.