Find the potential difference across each resistor in the figure below. (R₁ = 4.90 0, R₂ = 3.60, R₂ = 2.80, R₂ = 2.20 ) AVR₂ AVR₂² AVR3 AVRA 12.0 V V V V V 3.00 V R₁- www R3 18.0 V e

Q: Choose the right output of the following code Input Ladder logic program L1 -Input A Select one: O…

A: From PLC ladder diagramInput is switch AOutputs are lamps, Green, Red and Yellow

Q: DSB1(t) SSB1(t) DSB2(1) x10 SSB2(t) 0.001 0.002 0.003 0.004 0.005 0.006 0.007 0.008 0.009 0.01

A: SSB signal is single side band signal which is used in voice applications and used for analogue TV…

Q: If the four input lines of a multiplexer are DO, D1, D2 and D3, and the two select lines are given…

A: Four input lines of a multiplexer, and input for the select lines are 11 then find the output of…

Q: H\W: Assuming the SP=1236, Ax=24B6, DI= 85c2 and Dx=5f93, show the content of the stack and the…

A: Given, SP = 1236H AX = 24B6H DI = 85C2H DX = 5F93H Following Instruction to execute, ADD AX, SP PUSH…

Q: SIPO hardware converts: O Serial data into parallel data Parallel data into serial data Output data…

A: option A (SERIAL DATA INTO PARALLEL DATA)

Q: The following ASCII code 0000110 represents

A:

Q: a- Draw the circuit of 4-bits Johnson counter and draw its timing diagram

A: We’ll answer the first question since the exact one wasn’t specified. Please submit a new question…

Q: please dont use AI, it gives wrong answer thank u. solve by hand and i will like

A: Question i. a. If the ARM processor is configured as little-endian, it means that the least…

Q: Following is the segment of a 8085 assembly language program LXI SP, EFFF H CALL 3000 H 3000 H: LXI…

A: Solution !!

Q: To activate the ROM CS, the LS138 input must bes 001 011 100 110 111

A: The explanation is as follows.

Q: If the four output lines of a demultiplexer are YO, Y1, Y2 and Y3, and the two select lines are…

A: In this question , we will write output selected  for select lines 1 1...

Q: Compare between SUB & CMP instructions

A: Since there are multiple questions present, according to company policy we will be answering only…

Q: Q4/The initial content of the 4-bit serial-in-parallel out right shift register shown in figure 3 is…

A: Given:   In the above given sequential circuit they have mentioned the cascade connection of the 4 D…

Q: Write program to load the content of memory location 0x0700 into register R3 then set D6,D7 and…

A: The problem can be solved in the following way:

Q: QGive the State Machine for detecting the sequence "1010" from a serially coming a) Overlapping case…

A: The state diagram is visual representation of the sequence. It shows the internal states and…

Q: If the size of the memory is 1MB, what is the last address of the memory? A. Ох3FFFF OXFFFFF C.…

A: As per our company guidelines we are supposed to answer only first question kindly repost other…

Q: Thanks sir,perhaps you can attach also coding program Scilab using command plot2d3,please sir.

A: Given the signals:   x[n]={3,1,2,2} and h[n]={3,3,7,3} from 0 ≤ n ≤ 3. i) We need to provide the…

Q: If the four output lines of a demultiplexer ar YO, Y1, Y2 and Y3, and the two select lines a given…

A:

Q: please solve on a paper, no chatgpt

A: In little-endian systems, the least significant byte is stored at the lowest memory address. So,…

Q: 4 Bit Ring Counter

A:

Q: Design a combinational circuit with three inputs x, y, z and three outputs A, B, C. When the binary…

A:

Q: The logic function implemented by the multiplexer circuit is (ground implies a logic "0") 4x1 MUX 1…

A: Given- Multiplexer circuit Ground implies '0' input.   To find- The implemented logic function.

Q: Tristate buffers have three possible states.  Choose the correct terms for each state below: [Choose…

A: In this question, choose the correct option Which three states are exist in Tristate buffers ?

Q: 4 to 1 What is the value of J in SoP format? MUX C' 1 Flip-Flop А В Q 2 to 4 Dec AH O A'BC + AB +…

A:

Q: Question 2 In the machine language instruction 9F02, what is the opcode? 9F02 F02 9F 9.

A: Microprocessor and microcontrollers are used for data processing. Logic and control are used for…

Q: 4- What should be the value of { N } loaded to CX register in

A: Given Execution time=150micro sec Operating frequency=10Mhz

Q: At the end of the passing of the input string, the machine will

A: State diagram is a representation of present state input and next state output. According to the…

Q: Q13/Assume that the microprocessor can directly address 64K with a and 8 data pins The memory map…

A: We need to select address for chips .

Q: Fl in the resulting register values in the figure below Source register R5 0000 1111 1111 1100 0001…

A:

Q: Convert IEEE floating point number: 0 0111 1101 011 0000 0000 0000 0000 0000 to base 10, with work.

A: The given IEEE Floating Point Number is: IEEE floating point number=0 0111 1101 011 0000 0000 0000…

Q: You have used DEBUG to unassemble the following instructions. -U 0100 0108 1369:0100 B84365 MOV AX,…

A: The instruction is loaded at location 0106, the instruction takes two bits when the given code is…

Q: Problem 1: For the shift register in the figure below, assume that it contains 0000, i.e. Qo = 0, Q1…

A:

Q: What is the corresponding MIPS assembly language instruction for the following binary machine…

A: The MIPS instructions are 32 bits long. The starting 6 bits are used to specify the operation, this…

Q: Explain how the circuit shown in Figure 10 can be modified to create a 4-bit parallel in serial out…

A: The given figure shows the circuit of Serial IN parallel OUT shift register

Q: Write the necessary instruction to change or swap 3 byte stored at DS:0A60 with DS:0A80

A: