Design a combinational circuit with three inputs x, y, z and three outputs A, B, C. When the binary input is 0, 1, 2, or 3, the binary output is one greater than the input. When the binary input is 4 5, 6, or 7, the binary output is one less than the input. 1-16.

Q: Can you please help me design some instructions that ze ros the content of the accumulator register?

A: The given description is shown below.1Next step[1:0] 2_ 3Use_pc 4Load_mar 5arith 6invert 7pass…

Q: The output modules cannot handle as much current per output The input modules cannot handle as much…

A:

Q: Decoder circuit as shown in the following Figure. if A is LSB and C is MSB, the output expression F=

A:

Q: What is the function of the A, B, and D registers of the CPU12?

A: • The A and B registers are also called as accumulators and the main purpose of A and B register are…

Q: I need to create in a diagram a two to one with 1 bit multiplexer.

A: MUX: MUX represents Multiplexer. It's a combinational circuit. It has 2n no. of inputs and a single…

Q: A combinational circuit that converts 2" binary input lines to n binary output lines is called none…

A: Consider the block diagram of 8 (23 =8) input lines and 3 output lines. The encoder is the circuit…

Q: What is negative edge triggered?

A: The negative edge triggered means, the design changes its state only at the falling edge of the…

Q: Design counter that counts from 00 to 59, using the IC 74LS90 ripple counter and use two 7 segment…

A: Ripple Counter: Ripple counter is an asynchronous counter. The clock pulse ripples through the…

Q: Q1/ Answer the following questions? 1. List and explain LCD registers? 2. Human eyes emit -----…

A: The full form of LCD is liquid crystal display and the full form of LED is light emitting diode. Now…

Q: 2. Design a FSM to detect the "10101010" pattern. The circuit has an input signal, data-in, and an…

A: Given, Sequence to be detected = 10101010 Output= 1 only when detector detects 10101010 only.

Q: The instruction "BTG 0x89,3,1" takes. instruction cycles to execute. If the default RC oscillator…

A: Given data: Instruction is BTG 0×89,3,1 RC oscillator with TOSC=32 μs.

Q: With the following specification, find the hold slack of the below circuit clock period: 2.5ns clk-Q…

A:

Q: Define architectural registers.

A: • Architectural registers is a type of internal register of the processor.• It is defined as those…

Q: Question 2 Given Vcc=12V, at first the voltage inputs at Pin 6 and Pin 2 are both 10V. Decide the…

A: The solution is given below

Q: The 8259 PIC has 8 interrupt request (IRQ) inputs. Two 8259's can be to increase the number of IRQS…

A: The Intel 8259A Programmable Interrupt Controller handles up to eight vectored priority interrupts…

Q: What is the device address used by the instruction OUT A4, AL

A: OUT is a mnemonic that stands for OUTput Accumulator contents to an output port whose 8-bit address…

Q: How do I use Multisim to build a f4-input multiplexor using NAND gates only? Please use some…

A: The 4x1 multiplexer needs to be designed with the NAND gate and also the same needs to be…

Q: How does a serial in/parallel out register become serial in/serial out?

A: Serial in/parallel out:- The SIPO register is filled with serial information a single bit at a…

Q: If a DIP switch with 8 switches (0-7) lines up with bit0-7 of the data bus, and switches 1,2,4,5 & 7…

A: In this question,   We need to choose the correct options If switches 1,2,4,5 & 7 are set then…

Latches and Flip Flop

Just like logic gates, the latches and flip-flops are the important elements of an electronic circuit. The logic gates form the important part of combinatorial circuits, while the latches and flip-flops form the essential part of a sequential circuit. Sequential circuits form the important concept of automata theory in electronics and electrical engineering, these circuits are a kind of logic circuit whose output depends on both present input and past inputs, that is, the input history.