Find the hydrostatic pressure force acting on the ABCD curvilinear surface. (The width of the gate is 3 m). Draw hydrostatic pressure distribution on this figure. O Sex Appeal 2022 Full movie X(2) WhatsApp O Assignmer XINSANE RP EXPLOIT RANK XA HomeworkAKMRetake_E.pdf(2) WhatsApphttps://web.whatsapp.comАВРYou @ Okiki,lbrahim,BibiTayotoday at 7:00 amir2.4 mWaterWater1.6 mB.+

Answered: Image /qna-images/answer/dffbe7c2-8441-40cc-862d-f24f06cb77b6.jpg

Answered: Find the hydrostatic pressure force…

Find the hydrostatic pressure force acting on the ABCD curvilinear surface. (The width of the gate is 3 m). Draw hydrostatic pressure distribution on this figure.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

5 - An aluminum circular shaft, fixed at both ends, is loaded by torques applied at points B and C, as shown in the figure. The bar material has a shear modulus G = 85 GPa. Plot the maximum shear stress and angle of twist along the length of the shaft. A D TB 0.5m Tc 0.9m с 0.4m 40mm ↑ TB-10KN-m Tc=15KN.m
The solid circular section EF rod in the figure is fixed to the wall at point F. Forces P1 = 1 kN, P2 = 2 kN were applied from point D of the DE rod, which is rigidly connected to the rod. Calculate the stress states occurring at points A and B and show them on the small volume elements removed from these points. The diameter of the EF rod will be taken as d = 50 mm. Do not give answer in image and hand writing
3) Solve the following problem: The hollow tube ABCDE is made of a material that is subjected to five torsores that act as shown in the figure below. The outside diameter of the tube is d2 = 1.0 inches. The maximum allowable shear stress is 12,000 psi (12,000 lb / inch ^ 2). In addition, the maximum rotation per foot allowed is 2.0 degrees (2.0 degrees / foot). Take G = 9500 Ksi (9,500,000 psi). Note: Remember that 1 degree equals 0.0175 radians. Determine the maximum internal diameter d1, allowed for the tube.
A cross-section is subjected to a maximum shear of V=160 kN (see figure): Determine the centroid of the cross-section. Calculate the moment of inertia (I) of the cross-section. Determine the shear stress at point A in the cross-section.
N-S 2 A flow of a viscous fluid with µ = 1.0 μ has a velocity distribution given by u = 0.9y - y². The shear stress at y = 0.45 m is 2 (a) 0.90 N/m² (c) Zero m (b) ∞ (d) - 0.90 N/m²
The frame supports the distributed load shown. Determine the state of stress acting at points E and D. Show the results on a differential element at this point. 4 kN/m DA -1.5m-15m+ 3 m 1 BA 20 mm 60 mm 20 mm. 5m T D 50 mm
Situation The helical spring shown is axially loaded with a compression force P equal to 5 kN. The mean diameter of the spring is 100 mm and the wire used is 10 mm as indicated in the figure. 1. What is the shear stress at A? 2. What is the shear stress at B? 3. On diameter AB, locate the point of zero stress measured from C. P = 5 kN WW P = 5 kN 100mm A 10mm B
5 in? in. 3 in? 1 in? 500 lb. 1500 Ib. 20 in. 20 in. 20 in. E = 29 x 106 psi Member 1 2 3 a) Develop the system stiffness matrix for the three element bar shown. b) Use the applied loads and boundary condition to develop the restrained system stiffness matrix with the applied loads c) Find the deflections at each node d) Solve for the internal forces in each rod element e) Compute the strain energy in the structure. f) Verify the results that you found for c) by using classical approach, õ=(P.L)/(A.E)
Problem 6 For the structure shown in the figure, determine the normal and shear stresses at point A on the cross section of the pipe. at section a-a. mun 40 mm 300 mm 300 mm
The hollow circular beam is fixed to the wall (with a bracket) on the left and has an end-cap on the right. The cross-section is shown. (a) Determine state of stress at point A & draw the stress element (b) Determine state of stress at point B & draw the stress element A 100 k-in Tout 2 in n=1.75 in В. B 40 k-in C Tout 30 k X
X= 460 lb. Find the stress at points A and B. Determine the point where the neutral axis intersects like ABD. The neutral axis intersects AB at (blank) inches from A and intersects BD at (blank) inches from D.