Find the given values of the IC 555 timer circuit to work as Astable Multivibrator. а) find out duty cycle if Ra=5kohm and Rb=2kohm b) find out Ton if Ra=5kohm and Rb=2kohm and C=0.1uf c) find out Toff if Ra=5kohm and Rb=2kohm and C=0.1uf d) find out frequency(f) if Ra=5kohm and Rb=2kohm and C=0.1uf e) find out total time(T )if Ra=5kohm and Rb=2kohm and C=0.1uf_

Find the given values of the IC 555 timer circuit to work as Astable Multivibrator. а) find out duty cycle if Ra=5kohm and Rb=2kohm b) find out Ton if Ra=5kohm and Rb=2kohm and C=0.1uf c) find out Toff if Ra=5kohm and Rb=2kohm and C=0.1uf d) find out frequency(f) if Ra=5kohm and Rb=2kohm and C=0.1uf e) find out total time(T )if Ra=5kohm and Rb=2kohm and C=0.1uf_

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

How does a Phase-Shift Oscillator satisfy Barkhausen Criterion?
calculate the ripple voltage of a full wave rectifier with a 100-mF filter capacitor connected to a load drawing 50mA if the peak rectified voltage for a simple filter circuit is 30 V Ans. 27.90 V
Draw the 555 timer circuit that produces a square wave signal with Thigh=2ms and Tlow=1ms by calculating the resistor and capacitor values.
13. A biased parallel clipper is connected to a squarewave 20VAC input.The biasing voltage of 5V has the same polarity with the Vo while the Si diode is connected in reverse and will conduct only during negative half cycle.
What is the relationship between the frequency of oscillation and capacitance in an RC phase shift oscillator.
3. For the figure shown, draw the equivalent timing diagram of output Q. J PRE Q K CLR CLK J K PRE CLR
13. Pulse-amplitude modulation signals are multiplexed by using:a. subcarriers b. A/D convertersc. bandpass filters d. FET switches 14. A quantizer is a(n)a. multiplexer b. A/D converterc. demultiplexer d. D/A converter 15. Part of the PCM system that prevents aliasing:a. bandpass filter b. sample and hold circuitc. anti-aperture distortion d. both A and B
For the circuit shown below, if the oscillation frequency at the output is found to be 10 MHZ calculate the delay time of each stage Voo 10 Vout Select one: a. None of these b. 20 ns C. 10 ns d. 50 ns
A chopper has input voltage of 290 and the load resistance as 50, the average load current as 50A. If the non-conducting time of thyristor chopper is 120 Usec. Calculate the pulse width of output voltage in U sec. In case pulse width is 1/3rd for constant frequency operation, find new output voltage. Duty Cycle pulse width of output voltage in usec new output voltage
Q23.a. Find the values of rise time (tr), peak time(tp), settling time(ts) and maximum value from the following figure b. Draw the diagram of potential divider and explain its operation in the temperature measurement along with its output equation
3. Sweep Vin (0 to 1V) and plot Id. Vth = 0.4V. Indicate the region of operation clearly. 1V Jid Vin
I need the answer quickly