Find the generalized S-parameters of the following cireuit line where Z1 = 50 2 and Z2 = 75 2 (both lines are semi-infinite) and R = 50 N. Find the reflected-to-incident power ratio. Find the transmitted-to-incident power ratio. Z1 = 50 2 R Z2 = 75 A port1 port2

Find the generalized S-parameters of the following cireuit line where Z1 = 50 2 and Z2 = 75 2 (both lines are semi-infinite) and R = 50 N. Find the reflected-to-incident power ratio. Find the transmitted-to-incident power ratio. Z1 = 50 2 R Z2 = 75 A port1 port2

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: For the RG-214 cable listed in Fig. 1.10( c) determine the power loss at 0.1 GHz, when the input…

A: Given RG cable -214 frequency =0.1 GHz Length of cable l =5 m We need to determine power loss, Ploss

Q: three phase, 60 Hz transmission line has an inductance of 1.08 mH per Km per phase and a capacitance…

A: In this question we will find phase constant , surge impedance for lossless line...

Q: The observed standing-wave ratio on a 100-Ω lossless line is 8. If the first maximum voltage occurs…

A: Given: The observed standing-wave ratio on a 100-Ω lossless line is 8. If the first maximum voltage…

Q: A transmission line with 0.4? line length and 50 Ω characteristic impedance is terminated with load…

A: Hello. Since you have posted multiple questions and not specified which question needs to be solved,…

Q: A 50-N lossless line is terminated in Z, = 40 – j30 N. Determine the following: (a) the reflection…

A: A 50Ω lossless line is terminated in Z1=40-j30Ω. Now, to determine the reflection coefficient at the…

Q: Load impedance 30 + j10(N)is connected to the lossless transmission line 0. 101 à and characteristic…

A: Load impedance 30+j10 Ω is connected to the lossless transmission line 0.101 λ and characteristic…

Q: Write down the general expression for the input impedance of a transmission line of length 1 and…

A: "According to the Company's policy, we will solve only the first part of the question". We need to…

Q: Q2: For a (3-0) medium transmission line model (T cct) as shown in next figure, find the admittance,…

A: Given data are: The constants of the transmission line: A=D=0.861∠1° B=156.57∠78.35°…

Q: Question 2. For the transmission line shown in Figure 1 below, determine a) reflection coefficient…

A: Given: The transmission line is shown in figure below, Here, Characteristic impedance Z0=150 Ω…

Q: A lossless TL with if the voltage a cross a load connected to lossless TL is 20 Vms and reflection…

A: Since your question has multiple sub parts and you have not mentioned any part , we will answer only…

Q: Calculate Zin at the load using smith chart for total transmission lines, while the vavelength is 10…

Q: A loss less transmission line with reflection coefficient 3 ⁄ 13 at load end is terminated by a load…

A: The given problem is from transmission lines. The detailed solution is given in the next step

Q: mpedance of Z = 50+ j502. Calculate the reflection load. e: = 0.44263.43° %3D = 0.44Z-63.43° |…

Q: Q2: For a (3-0) medium transmission line model (T cct) as shown in next figure, find the, current…

Q: A 50-Ω lossless line has VL= 10ej25° V, ZL = 50ej30°. Find the current at λ/8 from the load

A: Given data The resistance of the transmission line, R=50 Ω. The voltage at the load end, VL=10ej25°.…

Q: Load impedance 30 + j10(N)is connected to the lossless transmission line 0.101 A and characteristic…

A: Load impedance 30+j10 Ω is connected to the lossless transmission line 0.101 λ and characteristic…

Q: The 0.1A length line has a characteristic impedance of 502 and is terminated with a load impedance…

A: Given data: load impedence ZL=5+j25 ohm. characteristic impedence Z= 50 ohm With the help of smith…

Q: For the transmission line below find Zin.Assume the frecuency of operation is 1GHZ and velocity of…

Q: Q2 Calculate the output voltages V, and Va in the circuit of Fig. 4.29. 2000 KO 20 k2 12 V =0.2 V…

Q: 763. (NEW) This is about two points, (x1,y1) and (x2,y2), on a straight line whose slope is given in…

Q: )10 to using 2's and 7's complement for

A: Code convertors- These code converters are used for conversion of one type of binary code to…

Q: A 50 Q air-filled transmission line of 3.45A is terminated in a load C. impedance of ZL = 90 - j30…

A: Given Zo = 50 ohm ZL = 90-j30 ohm L= 3.45 λ In smith chart we move towards the generator only…

Q: A lossless 1000 line is terminated with an inductance L=2mH. At w=25×10³rad/s, what is the…

A: In this question, We need to determine the reflection coefficient at the end of the line If…

Q: Problem 2: Given that the voltage standing-wave ratio S = 3 on a 50 O line, that the first voltage…

Q: A three-phase, 60-Hz. 765-kV transmission line has an inductance of 1.0071 mH/Km per phase and a…

A: Given Inductance and capacitance of a three phase transmission line.we need to determine the…

Q: We have a load with a return loss of 22dB, calculate the reflection coefficient I and the voltage…

Q: Q1. a) A 500 line is 0.1752 in length and is propagating a UHF frequency of 500MHz. For this…

A: Given, f = 500 MHz = 5 × 108 Hz Wave length, λ = vf = 3×1085×108 = 0.6 m Here, v - Velocity of light…

Q: Q6: Calculate Zin at the load using smith chart for total transmission lines, while the wavelength…

Q: b- Use the Smith chart to find the following quantities for the transmission line circuit below…

A: Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: 21. For a lossless transmission line, determine the value of the input impedance given: ZL = 25…

A: Dear,as per company guidelines we can answer only one question at a time, kindly post other question…

Q: Q5: A 50-W lossless line terminated in a purely resistive load has a voltage standing wave ratio of…

Q: Determine the primary constants, R, L, G, and C for a distortion-less line working at 300MHz. Given…

A: Given,Frequency, f=300 MHzCharacteristic impedance, Zo=75 ΩAttenuation constant, α=0.12 Np/mWave…

Q: The characteristic impedance of a lossless line is 50 ohm and the length of the line is half…

Q: A 60 n lossless line has a maximum impedance Z, = (180 + p) N at a %3! distance of /24 from the…

A: Reflection coefficients determine how much wave is reflected at discontinuity of medium.It is given…

Q: How do you derive the Telegrapher's Equations for a lossy transmission line? Why is it the bottom…

A: According to the question, we need to derive the Telegrapher's Equations for a lossy transmission…

Q: Q6: Calculate Zin at the load using smith chart for total transmission lines, while the wavelength…

Question

ANSWER HAVE TO BE CORRECT. PLEASE
PAY -ATTENTİON TO THİS . THANKS A LOT
Find the generalized S-parameters of the following circuit line where Z1 = 50 2 and Z2 = 75 2 (both lines
are semi-infinite) and R = 50 2.
Find the reflected-to-incident power ratio.
, Find the transmitted-to-incident power ratio.
porti
Z1 = 50 2
Z2 = 75 2
port2

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Single Phase Controlled and Uncontrolled Rectifiers

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

(please solve with complete steps both parts .i will give thumbs up)
For a parallel plate transmission line, since the relative dielectric constant is 2.5, the plate width is 30 mm, and the distance between the plates is 4 mm, what is the characteristic impedance of the line?
4 V IV 50 45 40 35 30 25 20 15 10 5 0 distance [cm] Zo = 602 ZL A 60 lossless line terminated by load Zz has a voltage wave as shown in the figure above. Find the standing wave ratios, the load reflection coefficient I' (magnitude and phase,,), and the load ZL- -Use numbers when answering, rounding to the tenths in the format 0.0 -Input your answer in the specified units for each parameter S= type your answer... [degrees] |T|= type your answer... Or = type your answer... ZL= type your answer... +j type your answer... [N]
On distortionless line, the voltage wave is given by 12010025 Los (10 t +21²) + 60 e -100251 Ve 6 " Cos (10² taze) where I' is the distance from the load. Assuming Z₁₂=3005², find a- 2, B, u b) Zo and Illit).
For the network shown in the Figure, if I53D5 mA and R=16 KQ, the power associated with the 20 KO resistor is: R V 0.01V 5 k2 I. 20 k2 Oa. 516 W Ob. 512 W Oc. 510 W Od. 514 W ww-
Solve it plz
A load impedance ZL = (45 - j60)2 is connected to a line that has a characteristic impedance 75Q. By using Smith Chart, determine the values for normalized load impedance (Z'), VSWR, reflection coefficient and angle of reflection coefficient (p20), load admittance (YL) and input impedance (Zin) when the length of transmission line is 0.062. 160o dihubungkan dengan talian yang mempunyai (45
For a loss less line, L = 1.2μH/m, C = 120μF/m and f = 200MHz. Prove the equation of characteristicimpedance of loss less line, Z0 and find the value of Z0.
i need answered quickly