Find the forces in members CE and CF in the figure below using the method of sections. Enter your answer in kN, and state whether they are in tension or compressions by using the standard sign convention. Enter the answer for member CE here, and the answer for CF in question 2. 2.4 m 2.4 m 2.4 m A 4 m D F G B. 80 kN 80 kN 80 kN

Q: I can't find C or D

A: Draw the free-body diagram.

Q: Consider a particle subject to the forces shown in Figure 1, where the forces have magnitudes

A:

Q: O Compute the Fore opplied an

A: Given details: F=1500 lbθ=45°

Q: d) Calculate the magnitude of the angle 0 in the Figure 1(b) that will maximize the moment of the…

A:

Q: Find the forces developed at pins E. 4 kN/m

A: Given

Q: Compute the moment arm for the force in cable C, measured relative to the AB axis. Use d₁ = 3.5 ft,…

A:

Q: If a 200 N force F1 is applied to the piston with the 4 cm diameter, what is the magnitude of the…

A: The step by step solution is provided below.

Q: A force F : about the point (1, 5, 0) ft. Find Fy. - 4i + Fj – 9k lb acts at a point (3, – 8, 6) ft…

A:

Q: 8000 lb D tur 4000 lb B 5000 lb H 9ft 9ft 9 ft 9ft 9ft-9ft 12 ft

A:

Q: a four-way lug wrench is horizontal. on one side the person pulls up with a force of 450n on the…

A: The free-body diagram of the forces acting on the lug wrench is shown below.

Q: Determine the magnitude and sense of the forces in bars A and B in the figure shown below. Show all…

A: Given data, A 80 k downward force is acting in a junction of bar A and B. To determine:- The…

Q: The boom has a negligible weight, but has sufficient strength to support the 1000N load. Find the…

A:

Q: Determine the magnitude of the forces. In the given figure, V = 300 N, V2 = 1.6 m, and V3 = 11 m.…

A: V1=300NV2=1.6 mV3=11mconsidering FBD of joint Cconsidering force qulibirium along x dirction…

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

A: Given data:- Vertical component of the force P = 300-IbTo find:-The magnitude of the force P

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

A: Force is defined as the push or pull type action which causes a moving object from motion to attain…

Q: 1. Measure di and d2 and record the values. 2. Record the total mass, M2, and include the mass of…

A: Given: The distance are d1=0.1 m and d2=0.1 m. The mass is M2=14 gm. The angle is θ=30°. The…

Q: A cylinder suspended by a rope rests against an inclined surface as shown. If the cylinder weighs…

A:

Q: Part I. Shorter problems focused on the fundamentals a. For the image at the right the coordinate…

A:

Work and Heat Transfer

It is generally related to thermal engineering which tells about the use, creation, conversion and transfer of heat energy between the systems. It is also considered that to transfer heat from one source to another, transfer of masses is also required. There are various mechanisms by which, transfer of heat takes place i.e. thermal conduction, convection, radiation or by change of phase. All these mechanisms have their own specific features which sometimes occur simultaneously within the same system.