Find the forces (F1,F2,F3 lb) in Fig. 364. (A=52, B=43, C=22) deg, (D=5, E=6, F=2) ft, F4=6230 lb If F4 is negative, then the direction of F4 is down. A negative answer indicates that the direction is reversed. Answers can be checked by demonstrating that components balance. ans:3

Q: In the figure, the 3.8 kg stone that is attached to the 0.42 m rope makes 60 revolutions each…

A:

Q: T 121 A 15 kg homogeneous pole with with a cable at B B 71° length of 5 m is raised by pulling

A:

Q: Determine the U and Y components of the 1000-N force shown below. Y 3 1000 N 2 38⁰ X

A: Angle between 1000N force and x axis  = tan-1(2/3) = 33.69° U component = 1000×cos(33.69°+38°) =…

Q: Write a torque equation

A:

Q: 1. Determine the magnitude and coordinate direction angles of the resultant force acting on the…

A: The resultant of two forces can be solved using the resolution of forces... F1 = 300 N  F2 = 500 N…

Q: If the force of each cable acting on the tower is shown, (Flgure 1) determine the magnitude of the…

A:

Q: Consider a 625 N cat burglar supported by a cable as in the figure. 35.8

A:

Q: Needs Complete solution with 100 % accuracy don't use chat gpt or ai plz plz plz.

A: Step 1:Mass of the teacher is 150kgStudents are lifting the teacher with 24m longConstant speed is…

Q: Q1: determine the resultant of the force system in next figure. And locate the resultant with…

A:

Q: Three forces F,= 20 N, F2 = 10 N and F3 = 5.0 N act on the structure shown in figure below. A fourth…

A:

Q: When tightening a bolt, you push perpendicularly on a wrench with a force of 161 N at a distance of…

A: Given: Force exerted, F =  161 N perpendicular distance of force from center, d = 0.120 m

Q: Problems x le | CAsers/ncate_000/Downloads/Practice.. a 3! Ri Looolt 45° 5. 21 Rz loo0 it here to…

A:

Q: 3. Draw a FBD that would enable you to calculate the force T' in the muscle. 55° 6". 5 lb G 13" 8 lb

A:

Q: 4. Determine the components of forces F and P along the X- Y axes which are parallel and…

A: Solution:-Given that

Q: The following setup made to find the experimental inertia for solid disk, given that step pulley…

A: The answer is OPTION C

Q: Four forces act on a particle that is in equilibrium where F3 and P are in the xz-plane. The…

A: Write the force F1 in vector form.Write the force F2 in vector form.Write the force F3 in vector…

Q: Two forces P and S, act on a ring, as shown. A. 07 R 1. Which of the following best shows the force…

A: We are given  forces. We find the resultant of 2 forces. We then find the magnitude and direction of…

Q: The force acting on the gear tooth is F=45 KN. Resolve this force into two components acting along…

A: Vector component diagram:

Q: Prof. K. climbed a wall and is now stuck and hungry. One of her ME 242 students saw this opportunity…

A: Let us look at the constraint relations after the rope has been pulled down a bit. Length of rope…

Q: F 1.5 m 1m D 2 m Fig.4 from Fig 4 Find intrenal force in member AB Where F = 67 KN

A:

Q: Replace the three forces shown by an equivalent force-couple system at point A. If the forces are…

A: Given that, R =  319 N M = 138.4 N m that is correct, So

Q: Question 6 The cable stays AB and AD help support pole AC. Knowing that the tension in AB is 240 lbs…

A:

Q: A force of 3.1 N makes an angle of 10o (counter-clockwise) with the +X axis. The Y component of the…

A: A force of 3.1 N makes an angle of 10o (counter-clockwise) with the +X axis. The Y component of the…

Q: example Homeware MB MA 7777777 30 MA = 30 kg MB = 10kg VALO V₁=0 Determine the acceleration of…

A: FBD of the block and the wedge.

Q: Question 1 1 of 1 Pulling a Weed The gardening tool shown in the figure(Figure 1) is used to pull…

A: Given, We use gardening tool to pull a weed. Required torque for pulling a weed is 1.36 Nm

Q: Needs Complete solution with 100 % accuracy don't use chat gpt or ai i definitely upvote you. Be…

A: The objective of the question is to determine the magnitude and sense of the forces in members A and…

Q: Can you please answer this question and show all of the steps

A: Horizontal cosine components cancel each other. The vertical sine components get added up.

Q: Below is a figure of a pulley system with two loads. Determine the expressions for the acceleration,…

A: Given m1>m2 And pulley has inertia I Let's draw the free body diagram Since in the same string…

Q: From the given figure, a screw attached on a concrete is subjected to forces F1 and F2, 4.1…

A:

Q: d. Two objects are hanging on the same pulley, as shown. 1.35 kg 3.75 kg

A:

Q: nd the magnitude and direction of the resultant force for the system of forces shown in the figure.…

A: Given F1=10N,F2=40N,F3=15N,F4=40N,F5=90N,F6=90N,F7=40N θ1=20,θ2=35,θ4=50,θ6=30

Q: force of 3.1 N makes an angle of 10o (counter-clockwise) with the +X axis. The Y component of the…

A: Y component is given by  Fsinθ

Q: 1. Ris the resultant of the four forces A, B, C, and D. Find the magnitude of the angle e and the…

A: Concept used: A vector can be split into sine and cosine components.

Q: Clamp Stand Figure 1 4 Leave the knife-edge of the first clamp at the center of mass of the stick…

A:

Q: In an experiment of moment of inertia and angular acceleration, the experimental moment o inertia…

A:

Q: Please answer fast Calculate the forces/torques for each question. A .The patellar tendon attaches…

A: Note: As per our policy, we are allowed to solve the first question, so, please post other questions…

Q: R= 35 N Q = 25 N 50 P = 20 N 30 50 S= 45 N

A:

Q: numbers with the right variable name - remember, the units are your best friend! A gear moving at 2…

A: Given:- ω0= 2 rad/secα = 1.4 rad/sec2ω = 12 rad/sec  Find:- The angle the gear moves through.

Newton's First Law of Motion

If a very smooth ball is rolled down an inclined surface with zero friction, the ball will continue to roll indefinitely for an infinite time, in an attempt to reach to the same height on the opposite hill!