Find the following: 1. The reaction at fixed end Rey II. The reaction at the fixed end Me III. The shear force at B IV. The bending moment at B V. Draw the shear force and bending moment diagrams for the

Q: Determine the maximum weight W of the block that can be suspended in the position shown if each…

A:

Q: Problem #2 6m YkN/m A B The support at 4 can be assumed to be a roller. Point C is an internal…

A: As per the guideline we are supposed to answer three subparts only. Kindly repost the question for…

Q: Find the reaction at support A RAy II. Find the reaction at support B RBY III. Find the bending…

A:

Q: The distributed couple acting on the beam is given by the equation c= (x/L)Co, where co is a…

A:

Q: (d) MN kN/m 5@2m = 10 m

A:

Q: The axial force at B is? 2. The bending moments at points C and E are?

A: Draw the free body diagram. Equilibrium of horizontal forces, ∑Fx=0Fx=0

Q: : Find the resultant force (R) of the two forces shown in Fig. below. F1= 55 N 25 F2= 65 N 35 30

A:

Q: Determine then,draw 2 k/ft the reactions on the beam. the shear-moment diagram 3 k/ft 600 k ft 12 ft…

A:

Q: 4 w kN/m P KN10 C D В A L1- L2- L1 - 4 2 4 Figure 2

A: Finding out SFD and BMD.

Q: 30 kN 10 kN/m A 6 m 2 m 3 m

A:

Q: Determine the reactions at the supports, then draw the shear and moment diagrams. El is constant 50…

A:

Q: In an experiment conducted by a soil engineer for the determination of the porosity and specific…

A:

Q: 45 kN 30° 7.5 kN/m A 3 m 3 m

A: Draw FBD:

Q: What is the reaction at B in kN? Replace the distributed loading by an equivalent resultant force…

A:

Q: Determine the vertical reaction at D, A, force in FBC, and force in FGC

A: Consider the figure,

Q: Find the support reactions at D and the tension forces in AC and AB. The beam has a mass of 100 kg…

A: Consider the free body diagram of the system. From the figure. tanθ=23θ=tan-123=33.69° Let the…

Q: The beam is subjected to a load F = 300 N and is supported by the rope and the smooth surfaces at A…

A: Draw FBD:

Q: Determine the reactions on the beam. then, determine the shear-moment equations 2 k/ft 3 k/ft 600 k…

A: Given:Required:Support reaction and shear-moment equation

Q: If the shear at point A on a beam is zero, then A.the slope of the bending moment at A must be zero…

A:

Q: 1. Determine the external reactions at the roller and pin supporting the above beam. 2. Determine…

A:

Q: A wooden beam is fixed at A. Four cables with forces "p" and "F" act on the beam as shown. a. Draw…

A: NOTE - Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the…

Q: (b) 5@2 m = 10 m SN KN

A:

Q: find the reactions at a and d

A:

Q: Determine the horizontal and vertical components of reaction at the pin A and the reaction on the…

A:

Q: Given: A frame is composed of lightweight rigid members ABCD, BE, and CEG. The frame is supported by…

A: (a)    F.B.D of ABCD ,CEG & Pulley G

Q: For the beam shown, using the Müller-Breslau principle, do the following: (a) Draw the influence…

A:

Q: (a) 4 m 6 m

A: Given data: Internal hinge at B:

Q: Problem 1 - A weight W = 200 N is supported by the two members AE and BD as shown. Joint C is a pin…

A:

Q: Since the beam is cantilever please solve the reactions at B only being fixed at that point. 60 KN/m…

A:

Q: In the following beam, prop reaction at 'B' is (EI = constant) Prop 2L B C

A:

Q: E 2 m A 3 m 4 m 52 kN 30° D B.

A:

Q: What is the reaction at B in kN? Replace the distributed loading by an equivalent resultant force…

A:

Q: d) How would you compute the reactions of this indeterminate structure using the force method,…

A: Given: UDL = 5KN/m  L= 5m Required: Reaction using force method

Q: The plane roof truss in the figure is acted upon by forces at joints C, E and J with magnitudes and…

A:

Q: -; For the frame shown below, determine the degree of indeterminacy and compute the reactions at D.…

A: Indeterminate structure: Any framework should be steady and not move unnecessarily when subjected to…

Q: The beam is supported by a pin at B and a roller at D. The applied loads shown in the figure have…

A:

Q: The reactions at the support for a simple beam loaded as shown. Neglect the weight of the beam. The…

A: Given: A simple beam with loadings  Required: Support reactions  Internal forces at C

Q: 1. Find the reaction atsupport ARAY x 2. Find the reaction at support BRBY 3. Find the bending…

A: As per guidelines please post ques 4,5 and 6 separately

Beams

In structural engineering, a beam is a component made of a variety of materials (including steel alloys, and wood) that can resist loads applied laterally to the beam axis. Members, elements, rafters, shafts, and purlins are all terms used to describe beams.