Find the distance x (m

Q: answer is 900.8 please resolve

A: Given Data

Q: How did you solve for the velocity of b?

A: The given question was solved using velocity polygon method.If AB is a link which is rotating about…

Q: Find the value of a. TO a. Vs +3

A:

Q: The pictured disk which weighs 20 lbs. and contacts an inclined surface (this inclined surface is…

A:

Q: The beam AB is homogeneous and has a mass of 5,191. The tension in the cable of the crane can not…

A:

Q: draw the left side

A:

Q: 10) in the following figure, if h2-10" and h1=5", then, the angle of taper equal 10" Ⓒa. 60⁰ Hand…

A: These are small blocks of alloy steel. Used in the manufacturing shops as length standards. Not to…

Q: Ax R.70 4x 1.40 B This part contains 4 holes with radius 0.375 inches 1.00 This part contains 4…

A: Select the correct statement about the notation circled in green and marked as letterA. Assume all…

Q: Forces and moments are scalar Forces are moments are vector quantities.

A: Forces and moments are both physical quantities that can be used to describe the behavior of objects…

Q: What is the maximum magnitude of the bending moment caused by force G? If none, enter zero. Do not…

A: It is required to determine the magnitude of the maximum bending moment by the force G.

Q: Your selection was a gas-turbine power plant operating on an ideal Brayton cycle and according to…

A:

Q: Answer in number 7 and 8.

A:

Q: The steel box wrench (E=29,000ksi, v=0.32) is loaded with a 40-lb horizontal force and a 25-lb…

A:

Q: 38. A belt is to transmit 50 kw power to a machine. The sheave is 10 inches in diameter and turns at…

A:

Q: Redraw when the rack AB is at 45o angle. What are the other two angles belonging to the triangle…

A:

Q: 0.75' C 4.5' Z 21-4 D A a 2 0.5' 2.5' B 10.5 X

A: (a) 2z ft(b) 0.5x+0.5y ft(c) -4.5x+0.75y+2.5z(d) -3.9x+y(e) 0.5x+0.5y-2z(f) 0.6x+0.25y-2.5z(g)…

Q: Solve 0.782bar in p/q form

A: Given that : x = 0.782782782....... We need to find it in the form of p/q

Q: ! Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

A:

Q: For the laser cutting of the shown path, determine the absolute and incremental coordinates of the…

A: given; findabsolute and incremental co-ordinate;

Q: Draw the and B A.F.D&S.F.D& B.M.D (KN.M

A: To draw axial ,shear and bending moment diagram

Q: Answer in 4-10

A: Given: →h1=3387.31 KJ/Kg→h2'=3074.5 KJ/Kg→h3=3457.04 KJ/Kg→h4'=3109.82 KJ/Kg→h5'=2384.82…

Q: The Answer is cut off on the right side.

A:

Q: Redraw when the rack AB is at 89o angle. What are the other two angles belonging to the triangle…

A: When the rack AB is at 89o angle. Draw the diagram as given above.

Q: 1- Sketch front, right and top views of the following object. Each grid represents 10 mm. Front

A: Given: Sketch Front, top and right side view of the given isometric view.

Q: Solve both and show all parts and solutions

A: The power to input shaft is The speed of gear of input shaft is The gear ratio is The loss in power…

Q: olve show full solution

A: To find:The principle stress at point A and absolute maximum normal stress at and absolute maximum…

Q: Express the quantity 254,998m in mm.

A: To convert meter quantity into millimeter one must be familiar with the no. of mm exist in one…

Q: 40 7 slug 110 dyne

A: given:

Q: The beam in the figure below is subjected to a load P= 3.9 kN at its end. Young's modulus is 210 GPa…

A: P = 3.9 kNE = 210 GPa I = 5 * 106 mm4a = 1.5 mb= 1.3m

Q: many hours did the carpenter work on the job? 6. What is the area of a rectangular floor that is…

A: Q.6 Given data as per question Length of floor = 7’-3” Width of floor = 4’-2”