Find the diameter of a solid steel shaft to transmit 15 kW at 300 rpm. The yield stress for the steel can be taken as 420 MPa and a factor of safety as 4. If a hollow shaft is to be used instead of the solid shaft, find the inside and outside diameter when the ratio of inside to outside diameters is 0.4. which is better to use the solid or the hollow? P 8:21

Find the diameter of a solid steel shaft to transmit 15 kW at 300 rpm. The yield stress for the steel can be taken as 420 MPa and a factor of safety as 4. If a hollow shaft is to be used instead of the solid shaft, find the inside and outside diameter when the ratio of inside to outside diameters is 0.4. which is better to use the solid or the hollow? P 8:21

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

ANSWER ASAP
The cross-sectional view of a closed section, thin-walled tube is shown in the figure. The thickness of the segments AB and BC is 4mm while it is 6mm forthe segments CD, DE and EA. If the tube material is Al 2014-T6 aluminum alloy, calculate the maximum torque value that can be applied safely on the cross-section. A E 200 80 B mm T mm D 200 mm 400 mm
A line shaft supporting two pulleys A and B is shown in figure below. Power is supplied to the shaft by means of a vertical belt on the pulley A, which is then transmitted to the pulley B carrying a horizontal belt. The ratio of belt tension on tight and loose sides is 3:1. The limiting value of tension in the belts is 2.7 kN. The shaft is made of plain carbon steel 40C8 (Sut = 650 N/mm2 and Syt = 380 N/mm2). The pulleys are keyed to the shaft. Determine the diameter of the shaft if, k = 1.5 and k, = 1.0. (Sm valing odi of 450 A B 2500 22.0=1821 P3 4500 250 ₁ 4500 P1 A P₂ P4
3. Find the power that can be safely transmitted by a flange type shaft coupling, if it has four equally spaced studs all at a radius of 50 mm from the shaft centre. The mean stud diameters are 12.5 mm, and each stud has a maximum safe working shear stress of 86 MPa. The shaft rotates at 3600 rpm.
Find the diameter of a shaft made of (37 Mn 2 steel) having the ultimate tensile strength as (600 MPa) and yield stress as (440 MPa). The shaft is subjected to completely reversed axial load of (200 kN). Neglect stress concentration factor and assume surface finish factor as (0.8). The factor of safety may be taken as (1.5). (After the diameter was found, correct it for the actual size factor). mechanical design pls solve fast
A cylindrical steel shaft is required to transmit a bending moment of 1000 Nm and a torque of 2200 Nm with a safety factor against yielding of 3. If the steel has a yield stress of 250 MPa, find the minimum permissible diameter for the shaft. Use von Mises’ theory of yielding.
Figure shows a cantilever shaft made of steel subjected to several loadingT=5kNm, M=2.5kNm, and P=120kN. If the diameter of the shaft is 60mm, and the yield stress is 310MPa, calculate the safety of factor of the shaft using the Von Mises yield criterion.
A simply supported shaft is shown in figure below. A constant magnitude distributed unit load p=1000 Nicm is applied as the shaft rotates subject to a time-varying repeated torque that varies with maximum value of Tmar=2000 N.m. Find the diameter of shaft required to obtain a safety factor of 2 in fatigue loading if the shaft is steel of S =745 MPa and S, = 427 MPa. The dimensions (I= 20, b = 18 and a = 16) are in cm.
A rigid coupling with 30 inches of bolt circle diameter transmits a torque of 18,000 lb-in. The coupling material has a yield strength of 90,000 psi. The coupling is fastened by six bolts. Assume design factor of N=3 Calculate the diameter of each bolt.
The steel shaft is made from two segments: AC has a diameter of 0.5 in., and CB has a diameter of 1 in. The shaft is fixed at its ends A and B and subjected to a torque of 500 lb-ft. Gst = 10.8(10³) ksi. (Figure 1) Figure sin. A 0.5 in. Jc 8 in D 500 lb-ft 12 in. 1 in. B < 1 of 1 Part A Determine the maximum shear stress in the shaft Express your answer to three significant figures and include the appropriate units. Tmax= Submit Provide Feedback μÅ Value 6 Request Answer Units www. ?
A solid shaft made from AISI 1040 cold-drawn steel is used to carry two V-belt, as shown in the Fig. 3. Pulley A receives power from a motor through a belt, with the belt tensions shown in Fig. 3. The power is transmitted through the shaft and delivered to the belt through pulley B. Assume the belt tension on the loose side is 10 percent of the tension on the tight side.