Find the current i(t) in the circuit, when i(0) = 1 A and the voltage is as shown in the graph. 1(t) = a,t + az for Os

Q: と。 O/ A balance 2-phose Y-Comecled \aad has z to 4-usa on Find phose Curents and live cnnnts.

A: Given data, Phase impedance is given, Zph=10∠-450 VCA is the voltage between line C and A therefore…

Q: which semi converter configuration, cathode of thyristors are connected in same potential point ?…

A: various configuration of the semi converter is possible which includes, asymmetrical and symmetrical…

Q: By visual inspection, are the two signals in phase or out of phase?

A: If two waveform is completely imposed into each other then it called in phase.

Q: Which of the following is essential condition of paralleling two DC generators? Equal currents Equal…

A: According to the question we have to discuss, the condition for the parallel operation of the two DC…

Q: what is meaning of contamination of condensate water and reasons and how to solve this fault, 2-…

A:

Q: Please answer. Thank you! Discuss the fault analysis in series-parallel circuits.

A: Fault analysis in a series paralleled circuits is an important aspect of electrical engineering and…

Q: Refer to the National Electrical Code or the working drawings when necessary. Where applicable,…

A: We are authorized to answer one question at a time, since you have not mentioned question you are…

Q: Name 3 applications for open-loop system

A:

Q: Why load characteristics goes lower with respect to the occ

A:

Q: Which stability is concerned with change of power angle ?

A: In this question , we will discuss about stability which associated with change of power angle..

Q: Design Synchronous counter with the sequence given below 1-4-6-7-0-1

A: we need to design synchronous counter.

Q: Differential between the high temperature Low Sag Conductors and Convetional converters,

A: To differentiate  between the high temperature Low Sag Conductors and Conventional converters. The…

Q: Determine the symmetrical fault in each bus as shown in figure.  Assume all pre-fault voltage to be…

A: To determine the symmetrical fault currents at each bus in the given 4-bus power system, we will…

Q: Shunt and undercompound generators are highly unstable for parallel operation compared to…

A: Answer is FALSE.         Shunt generators are most suited for stable parallel operation because of…

Q: What are two transform boundaries?

A: The transform boundary refers to a type of boundary where a specific type of transformation or…

Q: Think about the benefits and drawbacks of anticipatory standards vs reactive ones.

A: ***Anticipatory standards are standards that are established in advance of a particular event or…

Q: Choose the correct statement. A step-up power transformer has "a" greater than 1. O A step-up power…

A: In this question we need to choose a correct option.

Q: What do you understand by load equalisation explain how the load equalisation is done ?

A: Load equalization : Load equalization is the process by which any fluctuating load can be smoothen…

Q: Comment briefly on the relationship between input and output power at varying excitation levels and…

A: Infinite Bus Bar is the bus bar where many(infinite)  synchronous machines are connected.  The…

Q: The time available to turn-off thyristor in load-commutated chopper is 3-2E2Cf, 4-C, 5- None of…

A: The above question is based on load commutated chopper.

Q: The major advantage of single-bus designs is their low cost.

A: The major advantage of single-bus designs is their low cost.

Q: here not important?

A: Considering that the zone boundary along the number is surrounded by six upper valleyConsidering…

Q: ompare between 2-phas notor and universal moto

A: On the basis of the construction and working principle there are various types of motors like…

Q: Complete the timing diagram of the circuit shown below: clk D Q Հ D E clk clrn- clrn - պա

A: The given diagram contains two circuits one is combinational circuit called Multiplexer and other is…

Q: When two or more out of phase pulses interfere, they ____________. I. destroy each other   II.…

A: Pulse  is nothing but a disturbance or a deviation in voltage or current, interference is nothing…

Q: Adjustment resistance in rotor system will --------when three phase load .decrease Increase O not…

A: Adjustment resistance is also known as external resistance. Purpose of adding external resiistance…

Q: The cylindrical-rotor synchronous machine * is with is with maximum air-gap along the direct axis…

A: There are two types of synchronous machine: Cylindrical rotor synchronous machine Salient pole…

Q: Using Multisim please

A: The objective of this question is to design a traffic control system for a four-way intersection…

Q: Design Synchronous counter with the sequence given below 6-4-2-0-3-6

A:

Q: Main source of harmonics in the power system is Static power cinverter Resitive heating loads Power…

A: According to the question we have to discuss, the main source of harmonics in the power system.

Q: What is the difference between series and parallel circuits?

A:

Q: Apply mason Rule (S&P) to block diagnon below. кла то e(s) p Git 623 ST LGH H₂ 6₁ to H3 H₂ ((S) H₁…

A: A system is represented by block diagram. Signal flow graph is graphical representation of system.…

Q: In distribution substation, the shunt compensation used is of in nature.

A: in the shunt compensation shunt capacitors are connected in parallel with the line.

Q: What is the result of right shifting A1B3  four times?

A: Right shifting is done by using the register of the serial in serial out type register:

Q: A three way intersection is in need of a traffic signal control system and you have been assigned…

A: The traffic light, as everyone knows, is a crucial guarantee for keeping traffic order and ensuring…

Q: When plugging, as a general rule, the reversing contactor is of a larger size than the forward…

A: Step-1->   The answer is True. When plugging, a motor is started in the opposite direction.…

Q: 3-phase fault is the severe fault among all other faults True False

A: In this question , we will write about 3- phase fault severity...

Q: surge protector working principal

A: we need to state the working principle of surge protector

Q: How did you know you had to shift seven units to the right and then time reversal? Also, How do I…

A: Given:The solution of a problem , we need to find:How did you know you had to shift seven units to…

Thermistors

A thermistor is a special type of resistor whose resistance is more temperature-dependent than standard resistors.  The resistance of the thermistor decreases with increasing temperature. This is the basic principle of thermistors. This allows the thermistor circuit to detect very small temperature changes that cannot be observed with the Resistance temperature detectors (RTDs) or the thermocouples. Since the resistance of a thermistor is temperature dependent, it can be connected to an electrical circuit to measure body temperature. This high sensitivity to temperature changes makes thermistors very useful for accurately controlling and calibrating temperature measurements. In general, resistance increases with increasing temperature in most metals, but thermistors react negatively.