Find the cross sectional dimensions of the smallest square beam that can be loaded as shown in the figure if the allowable shearing stress is 1.0 MPa and the allowable bending stress is 8 MPa. 12 kN 4 kN m 4 m- 2 m 3 m-

Q: The ca jas z- 10GP3, has othe fos ortatA ASC EN

A:

Q: Define the term capillary fringe.

A: The capillary fringe is characterized as the saturated zone of water immediately just above the…

Q: Explain the term Cunningham correction factor.

A: Cunningham Correction Factor (C): In dynamics of fluid, the Cunningham slip correction factor is…

Q: Explain the  Swelling Index ?

A: The soil with clay minerals like montmorillonite, illite, and hallosite has the tendency to swell…

Q: For the beam and loading shown, (a) Use discontinuity functions to write the expression for w(x).…

A:

Q: Define undrained condition

A: If water is not allowed to flow in or out of the soil,  the stress path is called an undrained…

Q: I need information about waterproof work

A: Waterproofing work mainly used in construction works like building work for all the structural…

Q: 5. According to Fig. (a), (b), (c), specify what principle or relevant requirement is used on…

A: Dynamic tolerance diagram: Dynamic tolerance diagram 2 equal planes portray the volume of room used…

Q: Give details of JPCP, JRCP, and CRCP with necessary figures.

A: In pavement construction, three different concrete pavement design types are commonly used: Jointed…

Q: Define The width of the loaded area

A: Load: It is defined as the weight or force which is applied on the member, joint, or anybody which…

Q: What is Dimension D? Setback = 0.252, Bend Allowance = 0.345

A: The given values are as follows,The set back =0.252The Bend allowance=0.345To determine The…

Q: 2) fk= 4000 poi us= 150 pcf fy= 60ksi 36" FIND a) McR b) tc ce TOp) d fs @ Mr B0 c) tc ts e m 120…

A: Given - f'c = 4000psi W = 150pcf Fy = 60ksi

Q: Complete the table below. LINE BEARING DIST (M) AB N 57° 59.7° W 37.736 97.129 BC N 87° 3' E CD S…

A: Answer  Let us first calculate the latitude and departure of given lines Latitude = Lcosθ latitude…

Q: Activity Description Time Immediate Predecessors (Dependencies) А. Excavate None В. Foundation A С.…

A:

Q: QC is part of the QM process, is primarily concerned with process control during construction, and…

A: Solution:  The correct option to above question is option A

Q: fé = 4000psi, Grade 60, NWC Psteel = = = = Pb Please calculate As = ?

A: Answer  We are given b = 12 inch d = 18 inch h = 21 inch steel cover = 3 inch f'c = 4000 psi Grade…

Q: What is over-consolidated?

A: There are 3 types of consolidation stages namely : 1- over consolidation stage 2- normal…

Q: Define The shape of the loaded area

A: The shape of loaded area describes the intensity of loading at different sections and it's variation…

Q: Find CLR? ( ) Ib/ft3 (*No unit) QuR = 2.0 ft3/s CLR = ? Lb/ft3 Lodge Run QRR = 106.0 ft³/s• CRR = 0…

A:

Q: Define the Oweiss (1979) Influence Factor, a ?

A: A model known as the "Equivalent Linear Model" was presented by Oweiss (1979) which is essentially…

Q: What are the differences between on-site and off-site storage?

A: The difference between on-site and off-site storage is required to be considered according to the…

Q: Solve remaining part b. AASHTO classification

A: Given: Soil sieve analysis  To find : Soil name as per AASHTO classification

Q: 13. _________ is the process to determine the overall cost of project’s construction. Fill in the…

A: Processes of cost estimation are Empirical cost inference. Unit cost of bill of quantities. Types…

Q: Describe the TRD method.

A: TRD stands for Trench Re-mixing and Deep wall. It is a one-phase process for excavation and in situ…

Q: What is consolidation? Explain the concept of NCR and OCR with examples

A: Consolidation and the concept of NCR and OCR are explained in the next step.

Q: How MANY UNKNOWNS RESTROWTS MF thErE

A:

Q: 8. Define psychrometry.

A: To define:The term psychrometry.

Q: Define Boussinesq’s Method

A: The Stress Computation Method determines how the 3-dimensional stress distribution due to loading is…

Q: 4 L Derive Elymax. (

A: This question is related to the Strength of the material from Civil Engineering.  In this question ,…

Q: Construction cost of the manufacturing plant is considered as overhead cost. True False

A: Explanation :  The construction cost of the manufacturing plant includes direct and indirect costs…

Q: a. What is the length of the stretchout in inches?

A: At first an in. was the width of a man's thumb. In the 14th century, King Edward II of England ruled…

Q: In Midpoint Method, ag is equal to O 1.0

A: Question is not clear

Q: what is possible grade of service value ?  a.  -1 b.  3  c. 0.1  d. 1.1

A: Brief concept- Grade of Service (GOS) - It is the category of service and comfort that is provided…