Find the coefficient of uplift pressure of the elementary profile of gravity dam (for no tension at base) whose height is 50 m and base width is 35 m, Take Specific gravity of dam material is 2,65, 1. 0,61 2, 0,52 3. 0,46 4. 0,35

Q: 2. The maximum amount of solid waste collected per day for one week is presented below. All the…

A: Given, Municipal waste to energy combustion =100 tonsday

Q: Most real estate agents/professionals do not use the term 'situs,' rather they ask... What is your…

A: Situs is term that generally not used by many agents in real estate  Situs means physical location…

Q: An aluminum block show in Figure 9 is subjected to uniform pressure on all faces. If the chang ein…

A:

Q: This is incorrect, please redo it, I have attached what the correct answers are supposed to be S

A: For a given soil profile, there is an upward seepage occurring. The velocity of the upward flow, v =…

Q: A soil has the following soil properties for use in the Green-Ampt equation: K = 1.5 in/hr = -9.8 in…

A:

Q: Q.15 A concrete pedestal is made of M25 concrete as shown below. The value of tana for this case is…

A: Given data- A concrete pedestal- M25 concrete, qo=6 N/mm2. To Find- The value of tan α.

Q: Give me right solution according to the question.

A:

Q: Which of the following is a common connection method for prefab concrete wall panel systems? Panels…

A: For prefabricated concrete wall panel systems generally bolted or welded connections are used for…

Q: 33. Three pipes A, B and C have the following basic geometries Pipe A B Diameter D D/2 2D Length L…

A: Head loss Potential energy is turned into kinetic energy by head loss. The pressure loss due to…

Q: Problem 2. For a reinforced concrete beam, the cross-sectional dimensions are bxh-300 mmx600 mm,…

A:

Q: The diameter of a solid shaft is D. The inside and outside diameters of a hollow shaft of same…

A:

Q: A permeable soil layer is underlain by an impervious layer as shown in the figure. Knowing that k =…

A: Given data  H = 4.2 m  α = 6°  K = 4.8 × 10-3 cm/sec  Find seepage discharge in m3/hr/m width…

Q: Problem 2 A 1.0X102 N force in the j direction is applied to piping (ABCDEFG). The points in Fig 2…

A: Given data:- Force F =100 N The force vector is F⇀=(100 i+0 j+0 k) N The coordinates of points;…

Q: At a point on a steel part of landing gear (E = 200 GPa, v = 0.3, Oy = 225 MPa) subjected to a plane…

A: Given Data: 60 degree Strain rosette  εa=1200×10-6εb=-650×10-6εc=550×10-6E=200GPaμ=0.3σy=225 MPa

Q: 1. Determine the vertical displacement of joint B. For each member A = 400 mm², E= 200 GPa. Use the…

A: Virtual work method The virtual work approach, also known as the virtual force method or the…

Q: If a horizontal force P = 12 lb is applied to block A, determine the acceleration of block A.…

A: g=9.81m/s2 = 32.185ft/s2  mA = 8/32.185 lb  mB = 15/32.185 lb

Q: Determine the horizontal force reaction at joint 1. I l/ft A-9.12 in. 1-375 in. A= 103 in 1-285 in.…

A: To find the horizontal force reaction at 1

Q: Determine the magnitude of normal reactions at roller C (Nc), unit N. Set P = 123 N; a = 0,3 m. P…

A: We have to find the value of NC.

Q: Problem 1 AU-shaped tube is partially filled with a liquid of known density p1. At the right end,…

A:

Q: The 10-kg block A rests on the 50-kg plate B in the position shown. Neglecting the mass of the rope…

A: For the given block,

Q: Determine the magnitude Fand direction 8 (measured clockwise from the positive y-axis which is…

A:

Q: 2 – Response of the two-degree-of-freedom system shown in to an initial displacements of uj = 0.915…

A: Introduction- The responses of a two system indicates that the systems requires two independent…

Q: At 140 KPA, the soil's effective normal stage has a void ratio of 0.55. The soil's compression index…

A:

Q: 2. Slope and deflection at the free end. 20 kN/m -3 m 50 kN 2 m 40 kN 100 kN-m

A:

Q: 4. Evaluale the peak flow for the following catchment: A=200 ha, runoff coefficient= 0.5,…

A: Given data : Runoff coefficient (C)=0.5Area (A)=200 haPrecipitation intensity (i)=1 cm/hr

Q: Solve the area of the lot from the given data shown by triangle method. Course Observed Data…

A: Course Lattitude Departure Double meridian Distance Double Area (DA) AB -497.28 -56.66 -56.66…

Q: Handwritten answers 5.16

A:

Q: A timber whose thickness is less 50 mm and breadth is greater than 150 mm is called: (a) balk (c)…

A: Given data- Timber thickness less than 50 mmbreadth of timber greater than 150 mmTo Find-The type of…

Q: For the loading shown, use the double-integration method to determine (a) the equation of the…

A: Figure is as shown

Q: The coefficient of static friction between the 199.44-kg crate and the flat bed of the truck is u =…

A:

Q: A retaining wall 8 m high with a smooth vertical back retains a clay backfill with C = 15 kN/m2, o =…

A:

Q: of a cylindrical surface of which PN is the trace, supported by a structural frame The sector gate…

A: given- sector gate with cylindrical surfaceLength of gate perpendicular to paper 9m

Q: The design storm for a basin has the depth of rainfall for successive hours as 5.6, 7.6 and 5.2 cm.…

A:

Q: A concrete beam is post-tensioned by a cable carrying an initial stress of 1000 N/mm2. The slip at…

A: given- Initial stress=1000 N/mm2slip ∆=5 mm=5×10-3 mModulus of elasticity E=210 kN/mm2=210×1000…

Q: An exit sign is 16 ft (4.9 m) from an observer, and the smoke has the visibility listed here for 14…

A:

Q: Gusset Plate- Fy = 248 MPa Fu = 400 MPa 200 mm a) Determine the allowable tensile capacity of the…

A: Fu (ultimate tensile strength) = Ag x fy Fa(allowable tensile strength) = ϕ Fu = 0.75Fu Ag = 2 x L x…