A uniformly distrubuted load applied on a strip fooing constructed in sand. Based on Hansen's equations, for a given factor of safety (FoS = 3) find the required width (B). Water table is far below the base of fooing. 800 kPa 1.8 m q D Y Φ C g Nq FOS 20 35 B 20 m mm Ny 33.9 33.3 3 kN/m³ deg kPa m q B D

A uniformly distrubuted load applied on a strip fooing constructed in sand. Based on Hansen's equations, for a given factor of safety (FoS = 3) find the required width (B). Water table is far below the base of fooing. 800 kPa 1.8 m q D Y Φ C g Nq FOS 20 35 B 20 m mm Ny 33.9 33.3 3 kN/m³ deg kPa m q B D

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter7: Settlement Of Shallow Foundations

Section: Chapter Questions

Problem 7.2P: A planned flexible load area (see Figure P7.2) is to be 3 m × 4.6 m and carries a uniformly...

See similar textbooks

Similar questions

250 30/0 Priv Ter * Question Completion Status: 87°F Cloudy L 4 PA 5 6 Cross Section Area, A = 0.04 m² Axial Load, P = 171 KN Angle, 0 = 53° 7 # The bar is subjected to the axial load. There is a shaded section which is oriented at 0 from the horizontal. Given: 8 10 Moving to another question will save this response. LA A Determine the average normal stress (MPa) acting over the shaded section. Express your answer in 2 decimal places. $ 12 13 14 15 16 % P > S (C 17 & 18 19 hp W 00 20 6
A pipe carrying water has average height of irregularities from the surface of the boundary as 0.15 mm. The shear stress developed is 4.9 N/m2 and the kinematic viscosity of water is .01 stokes. Calculate roughness Reynold number.
A uniformly distrubuted load applied on a strip fooing constructed in sand. Based on Hansen's equations, for a given factor of safety (FoS = 3) find the required width (B). Water table is far below the base of fooing. 300 kPa m D |kN/m³ |deg kPa 20 35 C В Nq| Ny 33.3 33.9 FoS В Im
Situation 6: The pin is made of a material having a failure shear stress of Trail = 90 MPa. Determine the minimum required diameter (mm) of the pin to the nearest mm. Apply a factor of safety of F.S. = 1.9 against shear failure. Use P = 70 kN 무 P
1. Minimum design dead load for a 6mm floor fill (sand). a 0.015 kPa b. 0.023 kPaC. 0.0017 kPa D. 00.90 kPa2.The performance characteristics commonly of interest in the design of structures are the following except:a. Stresses B. Deflectionsc. Support Reactions d. Loading Condition 3. These structures are composed of straight members connected at their ends by hinged connections to form a stable configurationa.Rigid Frames b. Beams c. TrussesD. Slabs4. It is the portion of the slab area whose load is carried by a particular member.a. One-way systemb. Two-way system C.Tributary width d. Tributary area5. These are the actions of other bodies on the structure under consideration.a. Internal Forces b. External Forces C.Support Reactions d. Couple Moment
Q.9 A plate of area 2m² on which fluid flow with 2y² Y velocity profile as "= 7 5'where y(m) is distance from plate, u(m/s) calculate shear stress (N/m²) at y = 0.4m from plate, when flow is laminar. Dynamic viscosity = 0.015 Pa-s
AISI 1035 CD Steel Fy = 1.2 KN Fx = 2.5 KN Fz = 3 KN point is A. Find the factor of safety using Maximum Shear Stress failure theory. 50 300 40 50 25 40 Fy 35 380 Fx Fz
1.) The specific weight of the concrete is 150 ??⁄??3, and the coefficient of friction between the base of the dam and the foundation is 0.42. If the factor of safety against overturning is 2, compute for the minimum width of the dam. CHOICES a.) 8.416 b.) 4.681 c.) 6.841 d.) 1. 684 2.) The specific weight of the concrete is 150 ??⁄??3, and the coefficient of friction between the base of the dam and the foundation is 0.42. Use 1.5 as the factor of safety (F.S) against sliding. Calculate the width of concrete dam that is necessary to prevent the dam from sliding. Unit of the Correct Answer: ft CHOICES a.) 5,783 b.) 7.358 c.) 3.578 d.) 8.357
The specific weight of the concrete is 150 ??⁄??3, and the coefficient of friction between the base of the dam and the foundation is 0.42. If the factor of safety against overturning is 2, compute for the minimum width of the dam. Unit of the Correct Answer: ft a. 1.684 b. 6.841 c. 8.416 d. 4.681
Given: TABLE 3.1. Coefficients for Rectangular Bars in Torsion C2 0.1406 O.1661 0,1958 0.229 0.208 0.219 0.231 0.246 0 258 0.267 0.282 0.291 10 12 1.5 20 0.249 0.263 0.281 0.291 0.312 0.333 30 4.0 5.0 10,0 0312 00 0.333 Wood: Allowable stress: 5 MPa Shear Modulus: 0.5 GPa L= 0.6 m d = 50 mm
A 40m steel tape is suspended in the air between a theodolite and vertical rod, which is placed exactly at the 40m mark, under a pull of 12.5kg. The slope of the measured line is 2-degree 40minutes. The tape weighs 1kg, standard pull of 8.5kg, cross-sectional area of 0.039cm^2 and E= 2x106 kg/cm^2. Determine the correction for sag of the tape in meter. Determine the horizontal distance between the theodolite and rod in meters. (Apply 5-decimal places - for letter B only) What additional pull must be applied to eliminate the effect of sag?
2. WHAT IS THE MAXIMUM Pt Ре ↓ O O O 20 dia mm BEARING STRESS : 100 MPa SHEAR STRESS: 150 MPa STRESS: 280 MPa SAFE LOTAD? 130mm ->P I -P 25mm