**Problem Statement:**Find out the local convection coefficient for a flow over a flat plate at a distance of 0.2 m from the leading edge. The fluid is water at 60°C with a velocity of 2 m/s. The plate maintains a uniform temperature. Assume the film temperature to be 40°C. Calculated local convection coefficient: $ 6442.9 \, \text{W/m}^2 \cdot \text{K} $**Question:**Is the flat plate losing heat to or gaining heat from the water flow? Justify your answer.(Note: The phrase "gaining heat" is underlined in red, indicating emphasis on this part of the question.)

The distance is The water temperature is The water velocity is The film temperature is

Find out the local convection coefficient for a flow over a flat plate at a distance of 0.2 m from the leading edge. The fluid is water at 60°C with a velocity of 2 m/s. The plate maintains a uniform temperature. Assume the film temperature to be 40°C. 6442x9 W/m²K Is the flat plate losing heat to or gaining heat from the water flow? Justify.

Find out the local convection coefficient for a flow over a flat plate at a distance of 0.2 m from the leading edge. The fluid is water at 60°C with a velocity of 2 m/s. The plate maintains a uniform temperature. Assume the film temperature to be 40°C. 6442x9 W/m²K Is the flat plate losing heat to or gaining heat from the water flow? Justify.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An incompressible fluid flows over a flat plate with zero pressure gradient. The boundary layer thickness is 1mm at a location where the Reynolds number is 1000. If the velocity of the fluid alone is increased by a factor of 4, so what is the boundary layer thickness at the same location?
A pressurized gas at a pressure of 7 kPa and temperature of 30°C flows across a 0.3 x 0.3 m² flat plate at 7.45 m/s. The plate is maintained at 70°C. Estimate the heat lost from the plate. Given: µ=2.025x10$ kg/m,s, k=0.02798 W/m.°C Pr = 0.709 , p= 0.0754 kg/m
A horizontal thin plate with a length of L= 10 cm is tiled with a constant heat flux from the bottom and is cooled by air at the top. The air velocity is U = 40 m / s and the temperature is 20 ° C. What should be the minimum heat flux so that the plate temperature does not exceed 80°C? (kW / m²) v 17.94 x 10-6 m²/s = 0.0277 W/(m.K) Pr = 0.71
A square duct having D=23-cm and surface temperature T=70°C is located horizontally in an attic space with ambient temperature T=11°C. If the duct is subjected to ait flow of U=1.4-m/s, find the Nusselt number for the external flow over the duct as shown in the figure below. U air T
Air at 10°C and 1 atm is flowing parallel at a velocity of 15.5 m/s over the top flat surface of copper plate. The top surface of the copper plate is 0.03m by 0.03m square. The temperature of copper plate is uniform at 65.6°C. For laminar flow, calculate the dimensionless Reymolds number (Nre) and Nussel number (NNu). Table A.3-3a. Physical Properties of Air at 101.325 kPa (1 Atm Abs), SI Units Bx (Bp²/1?) T (kJ/kg · u x T (Pa ·s, k (W/m 103 (1/K • (°C) T (K) (kg/m³) K) -17.8255.41.379 1.0048 1.62 × 6s or kg/m · s) · K) Npr (1/K) m³) 0.022500.7203.92 2.79 x 108 O 273.21.293 1.0048 1.72 × (0-5 0.024230.7153.65 2.04 × 108 10.0 283.21.246 1.0048 1.78 ×/0 0.024920.7133.53 1.72 x 108 37.8 311.01.137 1.0048 1.90%/0-S 0.027000.7053.22 1.12 x 108 Select one: O A. NRe = 27826.58; NNu =98.58 O B. NRe = 23215.74; NNu =152.68 O C. NRe = 27826.58; NNu = 152.68 O D. NRe = 23215.74; NNu =98.58
A square duct having D=17-cm and surface temperature T=66°C is located horizontally in an attic space with ambient temperature T=14°C. If the duct is subjected to ait flow of U=1.0-m/s, find the Nusselt number for the external flow over the duct as shown in the figure below. U air T,
The space between two fixed plane surfaces is filled with SAE 15W-40 having Specific Gravity 0.89 and viscosity 178.01 mm²/s, at 30°C. A thin plate of 1.5 m² surface area is placed in between the two surfaces as shown in the Figure Q1(b) below. Evaluate the pulling force required to move the plate at a constant velocity of 1.2 m/s. Fixed Top plane surface 0.25 F 0.4 Moving Plate of 0.8 m² area Fixed Bottom plane surface
An incompressible fluid flows over a flat plate with zero pressure gradient. The boundary layer thickness is 1mm at a location where the Reynolds number is 1000. If the velocity of the fluid alone is increased by a factor of 4, then the boundary layer thickness at the same location, in mm will be 415
A fluid with a constant density of 961 kg/m3 and a constant viscosity of 1.419×10-3 Kg/m.s is flowing over a flat plate at a stream free velocity of 0.87 m/s. If the plate has a length of 2 m, answer the following: 1.What is Reynolds number at a point that is (1/4)L down the entrance? 2.Is the flow laminar or turbulent? 3.Calculate the thickness of the boundary layer in mm at (1/4)L down the entrance 4.Calculate the drag coefficient at (1/4)L down the entrance