Find I to set a Ø = 0.02 Wb on the right hand side. Below the material table to find (Flux density T (tesla) or Magnetizing force H (At / m) according to the material used. Data: N=250 vueltas Sı= 100 x 250 L2 = 300mm Factor de Apilameinto = 0,97 Li = L3 = 900mm I= ¿? S2 = S3= 100 x 160mm L1/S1 L3/S3

Find I to set a Ø = 0.02 Wb on the right hand side. Below the material table to find (Flux density T (tesla) or Magnetizing force H (At / m) according to the material used. Data: N=250 vueltas Sı= 100 x 250 L2 = 300mm Factor de Apilameinto = 0,97 Li = L3 = 900mm I= ¿? S2 = S3= 100 x 160mm L1/S1 L3/S3

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

5. Which of the following tests requires the supply to be energised? A) Continuity of circuit protective conductors B) Earth fault loop impedance Insulation resistance D) Continuity of ring final circuit conductors
What should be installed to power the DC water pump, from [stream-turbine-motor-________- water pump]? Do I need battery or Voltage regulator of this? It is better if you have an idea to suggest.
please answer all question which four ) no need to write your explnation 6.A current transformer is a A.transformer used with an AC voltmeter B.transformer used with a DC ammeter C.transformer used with a DC voltmeter D.transformer used with an AC ammeter 7.The primary winding of a current transformer has A.a larger number of turns B.a few turns only C.no turns D.intermediate number of turns 8/ Relation between primary winding and secondary winding for a potential transformer is given by A.n = Np ⁄ Ns B.n = Ns C.n = 1 ⁄ Np D.n = Ns ⁄ Np 9.Two wattmeters connected to measure the total power on a three-phase system supplying a balance load read W1 = 10.3 kW and W2 = –2.3 kW, respectively. Calculate the total power. A.–8.0 kW B.8.0 kW C.–12.6 kW D.12.6 kW
i need the answer quickly
List the basic concepts involved in house wiring?
21 Q2/ The one Per-unit impedaunce digram line digram 3-Phave pouser System. Draw the G: 50 MVA, 13.2 KU , Xg = 0.2 Pu Tig 30MVA , 13.2/220KU, XT,=0-1s P4 Te 30MVA, 22./11 kU, X+Z=0.15pu T3:30MVA , 13.2/132 kv, XT,=0.15P4 Tu:30MUA 132/11 KV, XTzo.15 Pu M: 70 MVA, lo.45kv, Xm =0.2 p4 Load, 53 MVA , lo.45kv, o.7 P.R (Lag) line1: 22o ku, Xline I=4oA %3D line2: 132 kv, Xlinez = 6or Te 220 132 36 Ty load 38 Select a Common base of 90MUA ,13.2kv on the generator Side
In which of the following wind energy conversion system, guy wire may be required? O a. Vertical axis wind turbines Ob. Horizontal axis wind turbines O c. Up wind turbines O d. Down wind turbines
When computing complex circuits, why is it advisable to use Kirchhoff’s Rules?
MSQ
10 - What is the figure below? A) Vavien switch installation B) Plug-socket installation C) Commutator switch installation D) Dimmer installation E) One-way switch installation
l11 answer 1 2 3
Which type of Insulator is used in Substations to support connections for High Voltage Switchgears, Current Transformers, and etc.? O A. STRAIN TYPE O B. PIN TYPE O C. POST TYPE O D. SUSPENSION TYPE