Use my matric number is (A20EA4013) of inertia about the centroidal r-ar.Q3.Figure Q3 shows a z-section with a hole where the center of the hole is located(а)Locate the centroid of the shaded area.ITTMUTMUTM OU.(b)UTMUTM(c)UTMExplain why there will be a difference between the valueinertia about the given X-axis and values obtained in (b).moment ofTM UTM2)UTM UTMUFM5 UM3 UTM/ & UTM & UTMUTMTM UTM 5 UTMJe3 UAMUTM &UTMTeircleUTM &UTM UTMTTMFIGURE Q33 UTMUTM & UTMTMLast digit of yourmatric card no.(E.g.: A21EAXXXX)0, 1, 2, 3 and 4STM UTM 5 UTMLength (mm)TABLE Q3TM UTMUTab5, 6, 7, 8 and 9110d240e2002001001003 UT50250100300150502508 UT30

Answered: Image /qna-images/answer/1d7a5a57-a25b-44c3-a710-2209e0e711e7.jpg

FIGURE Q3 Q3. Figure Q3 shows a z-section with a hole where the center of the hole is located (230, 130). Determine the following by using data tabulated in Table Q3. TUTM (а) Locate the centroid of the shaded area. TITM SUTM 5 UTM U (b) ITM &UTM * UTM STM (c) UTM UTM Explain why there will be a difference between the value of moment of a about the given X-axis and values obtained in (b). inertia UTM TM UTM UTM 5 UTM UTM. S UM 3 UTM & UTM & UTM UTM UAM UTM & UTM TM le UTM &UTM Icircle = Ar*/4 3 UTM UTM UTM TM FIGURE Q3 3 UTM UTM &UTM TM Last digit of your TM & UTM TABLE Q3 matric card no. (E.g.: A21EA×XXX) 0, 1, 2, 3 and 4 5, 6, 7, 8 and9 Length (mm) STM & UTM 5 UTM UT a b 110 d 240 e 150 200 200 250 100 100 100 300 50 150 250 30

FIGURE Q3 Q3. Figure Q3 shows a z-section with a hole where the center of the hole is located (230, 130). Determine the following by using data tabulated in Table Q3. TUTM (а) Locate the centroid of the shaded area. TITM SUTM 5 UTM U (b) ITM &UTM * UTM STM (c) UTM UTM Explain why there will be a difference between the value of moment of a about the given X-axis and values obtained in (b). inertia UTM TM UTM UTM 5 UTM UTM. S UM 3 UTM & UTM & UTM UTM UAM UTM & UTM TM le UTM &UTM Icircle = Ar*/4 3 UTM UTM UTM TM FIGURE Q3 3 UTM UTM &UTM TM Last digit of your TM & UTM TABLE Q3 matric card no. (E.g.: A21EA×XXX) 0, 1, 2, 3 and 4 5, 6, 7, 8 and9 Length (mm) STM & UTM 5 UTM UT a b 110 d 240 e 150 200 200 250 100 100 100 300 50 150 250 30

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

can you write step clearly
I am confused because on my homework i got marked wrong for this, unless I used to many sig figs.
Draw the right side elevation of the object with the given top and front elevations below
The open tank shown, which has a liquid with a specific gravity of S=127 as shown in the give figure, is accelerated upward at one g what is the pressure at point 1(kpa)? 150 cm 190 mm
Pls solve
Don't Use Chat GPT Will Upvote
نقطة واحدة B)) The vertical height of * ? point A from point B 40 m/s a=g= 10ms 20 m 18.75 m O 10.75 m 0.0 Sec O 1.5 m O 1.25 m 5.25 m O
ll a O ... 73 Your email address will be recorded when you submit this form. Not ahmed.yahya.engmsy@student.uobabylon.edu .iq? Switch account Required Q2:- To avoid interference, the value of the addendum must be:- * None of these On the gear is less than that of the pinion. All of these. On the pinion is equal to that of the gear. On the pinion is more than that of the gear. Q5:- The minimum number of pinion teeth in the rack and pinion arrangement of standard gear and pressure angle 20
Student Name: Reg. No: 1. Briefly describe Pascal's Law. Provide an examples of Pascal's Law applications in engineering. What is Revnolds Number what is the purnoss of Revnolds nunmber? State the
Calculate the Minimum Y distance on the drawing below: 1.000 O 2.000 O .460 O .510 1.966 O .500 C 2.000 Ø.995-1.000 6.00 0.008 MABC 3.000 Y 01.005-1.030 +0.005MABC B A .XX = .01 ANGLES= ± 1°
(24) States usually have their own building codes and state codes often require local building codes to be at least as strict as the state code. Select one: A. TRUE B. FALSE
Hello. Can you draw the OFF SET SECTION VIEW and the OBLIQUE SECTION VIEW of this figure? I don't need a very very good drawing. A sketch would be okay. Just indicate the proper section lines, and center lines. Thank you!