Figure Q2(b) shows three-phase balanced system in star- delta connection. Given three-phase voltage at the load is Vry = 208V20°V and the load impedance is ZLoad= (9 +j 12)N and then transmission line impedance is ZLine= (1+jl)N. Assumed the system is positivesequence, show all type of current and its value at the load on a phasor diagram.RZLineZLoadZloadNybZlineZLoadYBZuineFigure Q2(b)

Answered: Image /qna-images/answer/cd694bec-cf8c-4609-8836-d35ad38a8915.jpg

Figure Q2(b) shows three-phase balanced system in star- delta connection. Given three- phase voltage at the load is Vry = 208V20°V and the load impedance is ZLoad= (9 +j 12) N and then transmission line impedance is ZLine=(1+j1)N. Assumed the system is positive sequence, show all type of current and its value at the load on a phasor diagram. R Zuine ZLoad Zload N y b Zline ZLoad Y B ZLine Figure 02(b)

Figure Q2(b) shows three-phase balanced system in star- delta connection. Given three- phase voltage at the load is Vry = 208V20°V and the load impedance is ZLoad= (9 +j 12) N and then transmission line impedance is ZLine=(1+j1)N. Assumed the system is positive sequence, show all type of current and its value at the load on a phasor diagram. R Zuine ZLoad Zload N y b Zline ZLoad Y B ZLine Figure 02(b)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The 3-phase power equation in terms of phase voltage and phase current is /3VplpCoso 3VplpCoso
Question 3. A three-phase impedance load balanced D a connected load in parallel with a balanced ? connected load made of bonding. D each arm for the load ?D = 6 + 6? and ? each arm for the connected load It is given as ?? = 2 + 2?. ? the connected load ?? = 1? is earthed through the neutral impedance. To this impedance load, the symmetrical component voltages ?0 = 10∠60°, ?1 = 100∠0° and ?2 = Unbalanced phase-to-earth voltages ??, ?? and ?? of 15∠200° volts were applied. a) Draw the zero, positive and negative sequence circuits. b) Find the complex powers imparted to each component circuit.
Q2
9.2-2 Modal Dispersion. A step-index fiber of numerical aperture NA = 0.16, core radius a = 45 um, and core refractive index n, = 1.45 is used at A, = 1.3 um, where material dispersion is negligible. If a light pulse of very short duration enters the fiber at t = 0 and travels a distance of 1 km, sketch the shape of the received pulse: (a) Using ray optics and assuming that only meridional rays are allowed. (b) Using wave optics and assuming that only meridional (1 = 0) modes are allowed.
Given: 1. 2 wye-connected loads per phase to a 3 phase power source 2. first load consists of a 55ohm resistance and a 0.05H inductance per phase 3. second load consumes 1kW and power factor of 0.7 lagging per phase 4. RMS of voltage across the loads are 220V, frequency 120Hz per phase 5. single phase equivalent is shown in the figure: Question: What are the RMS line current at load 1 and 2 respectively?
Line Voltages at the terminal Pz:- The of abaancat Y conmected load is----- Each Phase of the load cousist of loL30 S2 Find the active s Reactive and somflex Power fer Phase then Find the total load. Var=12010, Powers for Heree phase
Problem: Given wye connected source: La Ven Van Von 6-1892 A 6-j802 N 6-j8Q2 I₂ Von = 120-120° V = 120 <-240° bn where V = 1200° an a) Find the line-to-line voltage phasors for the wye connected source. b) Find the line current phasors in each of the three phases of the resistive load. c) Find the current flowing in the neutral.
A three-phase system has balanced conditions so that the per-phase circuit representation can be used as shown in Figure 1 Select the turns ratio of the step-up and step-down transformers that the system operates with an efficiency greater than 99 percent. Moreover, find the complex power (received or given) of all components in the circuit and the V1 and V2 voltages. The load voltage is specified as 4 kV rms, and the load impedance is 4/3 ohm. ..
thats it
In the figure, bus 1 is the reference bus, V1 = 1.06 p.u and the angle is 0.. A load with active power= 100 MW and reactive power = 50 Mvar is connected to bus 2. The line impedance is z12 = 0.12 + j0.16 p.u on a base of 100 MVA. Start with an initial estimate of |V2|0) = 1.0 p.u and 820) = 0•. Find |V2| () (one iteration). 100 MW 212 = 0.12 + j0.16 ++ 50 Mvar Vị = 1.0/0° О а. |V2| (1) = 0.4 p.u. Ob. |V2| (1) = 0.5 p.u. Oc. |V2| (1) = 0.7 p.u. d. (1) = 0.8 p.u. е. |V2| (1) = 0.6 p.u.
Impedances Z1 = 5.83 at angle of -59 deg. and Z2 = 8.94 at an angle of 63.43 deg. are in series and carry an effective current of 5A. Determine the Power and power factor of the circuit indicating if it is leading or lagging.
A balanced load is connected in star across a 3 phasec415V 50Hz supply. The load consists of a coil of resistance 25 ohms and inducrance 0.5 henry in paeallel with a purw resistance of 28 ohms and a pure capaciror of 60microfarads capacitance ,in each branch. Calculate a. The line currents? Need full working and answer has to be 9.3A Formola for inductance XL= 2×3.142FL FORMOLA FOR CAPACITOR XC= 1/2×3.142×FC