Figure Q2 shows an 11 m long steel beam AC of uniform cross-section, simply supported at left end A and roller supported at location B. A uniformly distributed load of 40 kN/m is applied on the part AB of the beam together with a concentrated load of 20 kN at the end C. 20 kN 40 kN/m B 8m 3 m

Figure Q2 shows an 11 m long steel beam AC of uniform cross-section, simply supported at left end A and roller supported at location B. A uniformly distributed load of 40 kN/m is applied on the part AB of the beam together with a concentrated load of 20 kN at the end C. 20 kN 40 kN/m B 8m 3 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Question 2A rigid beam ABC is supported by pin at A and reinforced by a bar BD in order to sustain the uniform distributed load of 5 kN/m along the beam ABC in the direction shown in the Figure Q2.(a) Draw the free body diagram and determine the reaction forces at joint A(b) Determine the resultant force at joint A and its direction(c) Determine the internal loadings at section a--a
Problem 3 The boom AB supports a load of W = 720 lb. The boom is supported by a ball-and-socket joint at A and by two cables, BC and BD. Find the tension in each cable and the axial force in the boom, assuming that point C is 4 inches vertically above the position shown in the figure and the other dimensions are unchanged. Neglect the weight of the boom. -9 in.- 8 in. B 12 in. W = 720 lb %3D
show that the governing equation for axisymmetric stagnation flow is ϕ ′′′ + 2ϕϕ′′ − ϕ ′2 + 1 = 0 what is the thickness of viscous layer near the axisymmetric stagnation point?
SITUATION 1: A T-beam is simply supported and is used to carry a uniform load of 20 kN/m. The beam is 4m long and has the following properties of 5 the T-beam are as follows: bf=500mm; tf=D100mm tw=200mm; dw3300mm PAV
QUESTION 2 A beam supports a variably distributed load as shown in Figure 2. Given a pin support at A, and a roller support at B and the length of a is 2.8 m, calculate the vertical support reactions (in unit of kN). Assume upward and rightward are 'positive' and include the sign as part of your answers. You must include all necessary free body diagrams and intermediate calculations in your work solution. w = Wo-kx² A B. am 4m RA : 数字 kN RBY= kN
A new art exhibit featuring mobile works is going up in the Norwalk, CA area. One art work is shown in the figure below. A 105 N uniform beam is pinned to the ground by a pivot. The beam is supported by a cable (attached 3/5 from the bottom of the beam) to allow for each of the shoes to hang freely. Each individual shoe has a weight of 7.5 N. 10 WALL FLOR (a) ( If one shoe is attached 1/7 of the way up the beam and another shoe is attached 5/8 of the way up the beam, with e, = 70.1° and e, 30.1°, what is the tension in the cable, in newtons? %3! %3D (b) What is the x-component of the force, in newtons, that the pivot exerts on the bottom of the beam? (c) O What is the y-component of the force, in newtons, that the pivot exerts on the bottom of the beam?
Ciear Ly A beam (AB) is attached to a roller at A and a pin at B. It is subjected to three concentrated forces as shown in the figure below. The vertical component of reaction at pin B is. 3 kN 2.5 kN 1.5 kN30. 2m- 4 m 2 m- Select one: O a. 4.35 kN O b. 6.15 kN Oc. 3.35 kN O d. 1.25 kN Clear my choice 直0 üull lis sI FUJITSU
The simply supported beam is subjected to the loads as described in the figure and parameter table. Neglecting the thickness of the beam, calculate the horizontal and vertical support reactions at A and B. F A B C -4*- L3 parameter value units L1 L2 L3 ft 4 ft 6 ft theta 65 F 200 lb M 500 lb-ft For the answers, take to the right and up to be the positive directions. The support reaction at A in the z direction is NAz- lb The support reaction at A in the y direction is NAy- lb The support reaction at Bin the z direction is NB= lb The support reaction at Bin the y direction is NBy= lb
The horizontal beam ABC shown in thefigure is supported by columns BD and CE. Thebeam is prevented from moving horizontally bythe pin support at end A. Each column is pinned atits upper end to the beam, but at the lower ends, supportD is a sliding support and support E is pinned.Both columns are solid steel bars (E = 30 x 106 psi)of square cross section with width equal to 0.625 in.A load Q acts at distance a from column BD.(a) If the distance a = 12 in., what is the criticalvalue Qcr of the load?(b) If the distance a can be varied between 0 and40 in., what is the maximum possible value ofQcr? What is the corresponding value of thedistance a?
QUESTION 4 For the loaded structural beam shown in the Figure, the resultant support reaction at B is: 4 kN 7 kN 45° 30° B C. 1 m Im 15m 幸 · Beam O a. 4.46 kN Ob. 2.81 kN O c. 6.33 kN O d. 3.234 kN
Figure Q2 shows an 11 m long steel beam AC of uniform cross-section, simply supported at left end A and roller supported at location B. A uniformly distributed load of 40 kN/m is applied on the part AB of the beam together with a concentrated load of 20 kN at the end C. 20 kN 40 kN/m В. 8 m 3 m
The compound beam shown in (Eigure 1) is fixed at E and supported by a rocker at A and B. There are hinges (pins) at C and D. The 4-kN load is applied just to the right of the pin at D. Suppose that w = 5 kN/m. Figure 4 kN 6kN I. conf 1 of 1 -2m-2m-2m-3m- 3m ▼ Determine the y component of reaction at A. Express your answer to three significant figures and include the appropriate units. A₁ = Value Submit Part B B, = HA Submit Part C Request Answer Determine the y component of reaction at B. Express your answer to three significant figures and include the appropriate units. Value KN Request Answer ? KN ? Determine the component of reaction at E.. Express your answer to three significant figures and include the appropriate units.