A beam with a solid homogeneous rectangular section is simply supported at A and B.   A concentrated load F = 150 kilonewtons (kN) acts at point C where distance L1 (A to C) = 2.50 metres (m) and distance L2 (C to B) = 1.65 metres (m). The dimensions of the rectangular section of the beam are breadth, b = 35 mm and depth d = 125 mm. Calculate the maximum bending stress and give your answer in N/mm2 to two decimal places

Q: For the beam -section below, calculate the second moment of area about its centroidal y-axis…

A: We need to calculate the second moment of area of I beam

Q: Determine the support reactions at A for the beam with built-in ends. 900 N/m -2 m-

A:

Q: Q2: Simply supported beam shown in Figure hinge at point A and roller at point B. Determine the…

A: Deflection in beam is the measure of sag occurred in the beam in vertical direction. This sagging of…

Q: alculate the reactions at point A  for the beams shown. (Clockwise rotation of a moment - Negative,…

A: Total weight of the udl = 1(14+10)=24K it acts 12' from the A supports Using the conditions of…

Q: 4 kN A 30 6 m -2 m

A:

Q: For the beam shown, use only singularity functions. V₁ = 45 lbf/in and V₂ = 5 in. NOTE: This is a…

A: Given,

Q: Q2: A simply supported beam AB has a length of 3 m and carries distributed load which varies in…

A:

Q: The structure shown below is hinged to fixed supports at A and C. The bars are each 4 in. by 4 in.…

A:

Q: Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

A:

Q: Question # 3:A horizontal beam AB 6 m long is hinged at A and freely supported at B. The beam is…

A:

Q: The beam ABC has three supports and carries two equal but opposite couples. Determine all the…

A: Given data: M=2000 lb.ft Need to determine the support reactions.

Q: A cantilever beam of length Lis subjected to a concentrated load Pat a distance of L/3 from the free…

A: Given            Total length = L Concentrated load = P Load act at L/3 distance Find   Deflection

Q: Q2: Simply supported beam shown in Figure hinge at point A and roller at point B. Determine the…

A: When any beam is subjected to a load, it deflects, and the neutral axis becomes a curved line which…

Q: Q2: A simply supported beam AB has a length of 3 m and carries distributed load which varies in…

A:

Q: A simply supported beam 6 m in span is supported at supports A and B. The beam is acted upon a…

A: Draw the free body diagram of the beam and calculate the reactions. Consider the equilibrium of…

Q: Determine the value of Elv (in Ib ft³ )at midspan for the beam loaded by two concentrated forces if…

A:

Q: . The two 12 ft. beams shown are move horizontally with respect to each other and load P shifted to…

A: Consider the diagram as shown below for the given beam.

Q: USE IMAGE BELOW Question; Draw and fully label the Freebody diagram of the BEAM in the picture…

A:

Q: Determine the reactions at the fixed end (A) for the cantilever beam with the distributed load.…

A:

Q: There is a doubly embedded circular beam, (diameter = 60cm) and (G=2x10⁴ kg/m²) It is requested

A:

Q: The floor plan of a building is shown in the Figure below. Using the Ultimate Design Load given, (1)…

A:

Q: Beam ABC is subjected to the loading shown, where PB = 75.0 kN. The measurement corresponding to the…

A: To findDraw a free-body diagram.Determine the maximum shear force  in beam ABC.GivenLoad, Length,

Q: The V-shaped beam shown in Fig. 4 has a fixed support at O, and is subjected to an 8 kN point load…

A:

Q: The simply supported beam supports a uniformly distributed load of w=240 lb/ft between supports A…

A: Given:To find:Principal stresses and maximum shear stress at point K.

Q: Q2: A simply supported beam AB has a length of 3 m and carries distributed load which varies in…

A: Draw the free-body diagram of the beam along with the beam.       Apply force equilibrium in a…

Q: 2. A simply supported rectangular concrete beam of span 8m has to be prestressed with a force of…

A:

Q: At what distance, "a" should the bearing supports at A and B be placed so that the displacement at…

A: Given data: EI is constant