Figure Q1 below shows a gear reducer unit which drive a cement mixer drum at output of this unit and attached to a motor at the input. A 1.5 kW motor with a speed of 9 33 rpm is used as an input source to drive this gear reducer. The gear reducer consists two pairs of spur gears which each pair of them have modules of 1.5 mm for gear set 1 and 2.5 mm for gear set 2. All the spur gears have 20 deg pressure angle.

Figure Q1 below shows a gear reducer unit which drive a cement mixer drum at output of this unit and attached to a motor at the input. A 1.5 kW motor with a speed of 9 33 rpm is used as an input source to drive this gear reducer. The gear reducer consists two pairs of spur gears which each pair of them have modules of 1.5 mm for gear set 1 and 2.5 mm for gear set 2. All the spur gears have 20 deg pressure angle.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The total conversion rate of a two-stage gearbox is 53, the conversion rate of the second stage is 1.5 times the conversion rate of the first stage. If the number of teeth of the gear mounted on the input shaft is z1=27 and the number of teeth of the pinion of the second stage is z3=33, how many teeth are the gear z2 of the first stage?
part 3 plz
There is a motor with a power of 38 HP. The driving pinion has a speed of 20 rpm and the driven pinion of 5 rpm. Design the driving pinion and driven pinion based on the rpm of each pinion. do not forget the module and the number of teeth for each pinion. Gear ratio value: i= 5 rpm / 20 rpm = 0.25
The figure below shows a two-stage helical gear set. Pinion 2, which is in the converter position, transfers a certain rotation moment from the shaft to gear 3 in the first stage by rotating in the direction of the clock in the front view (or in the Z direction) shown in the figure. on shaft B, the pinion gear No. 4 is positioned with gear No. 3, which receives and/or transmits the drive from different gears. The number 4 Pinion in the second stage drives the number 5 gear, converting the input moment in the system to the output moment and providing movement transfer. Answer the figure in the table as follows by determining the direction of rotation of Gears 3, 4 and 5 and the Helix direction of each gear when looking at the left side view of the figure from the left (i.e. from the-z direction).Also, briefly explain how the concept of a module in Gears is determined by showing the basic dimensions on a tooth form and what the main law of gears refers to by drawing a figure.
Hello, could you please help. i need to work out the holding torque, thanks
b) Figure Q1b shows a compound gear train with Gear A as the pinion (or driver) with an input Power (Pin) of 600 W at Gear A. If Gear A rotates at 139.70 rpm and engages with Gear B, calculate the angular velocity (w) in rad/s for Gears B, C & D; and the input torque (Tin) in at Gear A and output torque (Tout) at Gear D. The number of teeth (N) for gears A, B, C & D are 62 teeth, 34 teeth, 42 teeth and 22 teeth, respectively. Assume 100% efficiency and no frictional losses; and give your answers to two decimal places. GEAR A GEAR C GEAR B GEAR D
1. The figure below is a spur gear train drive and gear 2 is the inlet of the gear train. It transfers 12 kw of power at 1200 rpm. Gear 3 and 4 have 60 and 20 teeth respectively and are made with 20° pressure and full-depth teeth. The desired speed for the output shaft is 32 rpm. a. Find the minimum number tooth on gear 2 to obtain 32 rpm at the output and confirm its validation for interference-free power transfer. b. Find the speed ratio at each gear set using the results obtained at "a"(above). c. Determine the rotational speed of each gear (n2, n3, n4, and n5) using the results obtained at "a"(above). d. Find the torque of each shaft (Tin, Te, Tout) assuming that there is no frictional loss during the power transfer. e. Determine the radial, tangential and total forces transmitted at the last gear set assuming a module as m=4 mm, and draw the free body diagram of gear 4 showing the forces and torques. 75, 100 2007 In Out 4
In the textbook (Machine Elements in Mechanical Design 6th Edition by Robert L. Mott, Edward M. Vavrek, and Jyhwen Wang) chapter 7 problem 78, I'm having trouble trying to understand and solve it with the information given to me. Image below.
I need answer within 20 minutes please please with my best wishes
Two spur gears are to have a ratio of 9:3 and a 7mm module. If the center distance is to be approximatively 200mm, calculate the following:o Circular pitch value;o Number of teeth on the wheel (gear);o Number of teeth of the pinion;o Pitch circle diameter of the gear;o Pitch circle diameter of the pinion;
Please assist
Please help me finding this question. Power = 6 kW