Figure P3-36 shows a beam made from 4 in schedule 40 steel pipe. Compute the deflection at points A and B for two cases: (a) the simple cantilever and (b) the supported cantilever. -6 ft. +4 ft → -8 ft. 800 lb B (a) Simple cantilever 800 lb B -10 ft- Support (b) Supported cantilever

Figure P3-36 shows a beam made from 4 in schedule 40 steel pipe. Compute the deflection at points A and B for two cases: (a) the simple cantilever and (b) the supported cantilever. -6 ft. +4 ft → -8 ft. 800 lb B (a) Simple cantilever 800 lb B -10 ft- Support (b) Supported cantilever

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Problem 2 (a) Please compute and plot the shear force and bending moment diagrams for the beam shown below in Figure 2.1. Please use the method of sections to get the equations for shear force and bending moment, and use a computer to plot the diagrams and get the maximum value of bending moment. (b) For beam in problem 2-(a), suggest the lightest-weight wide-flange beam (use Appendix B) made of A-36 Structural Steel that avoids yielding with a factor of safety of at least 2. Use Sy (σy)=250 MPa. 50 kN/m Hinge 3@2m 6m = Figure 2.1
Problem 3 For the beam shown in the figure, a) Derive the equation of the elastic curve. b) Compute the rotation at point B. c) Calculate the deflection at point C. Y 2.7 kN.m Y 300 N/m B 3m 3m 3m 3m
a beam is supported by a pin support at A and a roller support at B. For this question, leave your answer in terms of the variables w and L. (a) Using equilibrium of the full beam, find the support forces at A and B. (b) First section: Make an arbitrary cut between points A and B. Take the distance of the cut to be x along the beam from point A. Draw the free-body diagram for the left section and find functions for the internal shear force, V(x), and bending moment, M(x), in the section of the beam between A and B. (c) Second section: Repeat part (b) for the section of the beam between B and C. Take x to still be the distance from point A. (f) Find the value of x at which V(x) = 0. The internal bending moment reaches a maximum at the same point as V(x) = 0. Find the maximum bending mo- ment. pin Sketch the shear and bending moment diagrams. B L W C roller
Perform double integration of the bending moment equations. You will obtain deflections in this form (can be found in the image attached) Calculate: the value of the constant integration C2. Enter your answer in kNm2 to three decimal places. b) the value of the integration constant C4. Enter your answer in kNm2 to three decimal places. c) the value of the deflection at point C. Enter your answer in mm to three decimal places.
The cantilever beam shown in figure is built into a wall 2 ft thick so that it rests against points A and B. The beam is 12 ft long and weighs 100 lb per ft. Force P is equal to 0361 Solve for the Ra & Rb. Plb 10 ft 100 lb/ft B 2 ft Show your complete solution and tabulate your answer properly.
For the shaft in Problem-1, compute the deflection if the load is placed 175 mm fr the left support rather than in the center. Compute the deflection both at the load at the center of the shaft
In Problems 8-51 to 8-68, beams are loaded and supported as shown in the accompanying figures. Draw complete shear and moment diagrams for 5000 lb 8000 Ib B. -4 ft 5 ft 4.5 ft
The frame in (Figure 1) supports the 350lb load. The pulley at C has a radius of 0.5 ft. The pulley at D has a radius of 0.25 ft. a) Determine the reaction at pin A. b) Determine the reaction at pin B.
A schematic of a homemade hydraulic jack is shown in the figure below, with cylindrical tube ends of different radii, r, = 0.0440 m and r, = 0.120 m, respectively. F A (a) If a downward force of F, = 16.0 N is applied to the end with the smaller radius, how much force F, would the jack exert on a car if it were sitting above the other end? (Enter the magnitude.) N (b) If the smaller piston is pushed down a distance d, = 0.208 m, through what distance d, would the other end move?
The given figures shows a cantilever of spa L subjected to a concentrated load Pand moment Mat the free end. Deflection at th free end is given by 7. M.
es A gear reduction unit uses the countershaft shown in the figure. Gear A receives power from another gear with the transmitted force FA applied at the 20° pressure angle as shown. The power is transmitted through the shaft and delivered through gear B through a transmitted force Fg at the pressure angle shown. For the steel countershaft specified in the table, find the deflection and slope of the shaft at point A. Use superposition with the deflection equations in Table A-9. Assume the bearings constitute simple supports. In the figure below, FA is 310 lbf and the diameter of the shaft (dshaft) is 1.29 in. dshaft Gear A 20-in dia. 16 in FA 20⁰ The deflection at point A is The slope at point A is 14 in 100 Gear B 8-in dia. rad. 9 in in. B FB 20°
Compute the initial deflection of the beam at midspan under service loads with the following specifications: f'c = 4000 psi, 36-inch height, depth of rebar assumed to be 3 inches less than the height, 16-inch width, 4 #9 bars (tension), Grade 60 rebar, 30' clear spans, service loads of: DL = 0.25k/ft, LL = 1.2k/ft. The DL does NOT include self-weight of the beam or of the precast concrete deck planks that have a weight of 60 PSF. The beam picks up a tributary width of 12 feet. Also, note that this beam is continuous and is the middle beam of 5 equal spans. Check the initial deflections against the ACI deflection requirements. Then calculate the long-term deflections and check those against the ACI requirements. For both situations, assume that finish materials will be attached to the beam. Last: Instead of performing a structural analysis to determine the maximum deflection in the beam, conservatively figure that the maximum deflection will be 60% of what it would have been for a…