Figure P18.26 shows a voltage divider, a circuit used to obtain a desired voltage AVout from a source voltage E. Determine the required value of Rg if E = 5.00 V, AVout = 1.50 V, and R = 1.00 x 10 0. (Hint: Use Kirchhoff's loop rule, substi- tuting AVout = IR2, to find the current. Then solve Ohm's law for R2.) R1 R AV out Figure P18.26

Figure P18.26 shows a voltage divider, a circuit used to obtain a desired voltage AVout from a source voltage E. Determine the required value of Rg if E = 5.00 V, AVout = 1.50 V, and R = 1.00 x 10 0. (Hint: Use Kirchhoff's loop rule, substi- tuting AVout = IR2, to find the current. Then solve Ohm's law for R2.) R1 R AV out Figure P18.26

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

In the figure the ideal batteries have emfs E1 = 4,89 V and E2 = 10.2 V, the resistances are each 2.41 Q, and the potential is defined to be zero at the grounded point of the circuit. What are potentials (a)V1 and (b)V2 at the indicated points? R. R3 Units (a) Number Units (b) Number
A circuit consisting of three ideal batteries with voltages ℰ1,E1, ℰ2,E2, and ℰ3,E3, and three ideal resistors with resistances ?1,R1, ?2,R2, and ?3,R3, is shown in the figure. Calculate the current ?PIP through point P. Let the sign of the current correspond to its direction, with "up" being positive. ℰ1=16.0 V, ℰ2=15.0 V, ℰ3=27.0 VE1=16.0 V, E2=15.0 V, E3=27.0 V ?1=2.30 kΩ, ?2=22.5 kΩ, ?3=2.25 kΩ
Consider the circuit shown in the figure below, where R, = 8.00 N, R, = 7.00 N, and Ɛ = 11.0 V. %3D 10.0 N R2 5.00 N 2.00 N R1 (a) Find the voltage (in V) across R,. V (b) Find the current (in A) in R,. A
Ginko has two parallel plates which are uncharged. They are connected to the RC circuit shown below. Ginko knows the following things abaout this RC cuircuit: The C1 capacitor is filled with air, The C1 capacitor has a plate area of 6cm^2, The C1 capacitor has a plate seperation of 0.500mm, The C2 capacitor is filled with with cardborad that has a dielectric constant of 3.7, The C2 capacitor has the same separation as C1, The C2 capacitor has twice the plate area of C1, The switch remained at a for a long time and then was throuwn to b. Figure out the final charge on each capacitor. b C₂ C₁ 18.0 V 2.00 kn Ginko
R1 R2 2. Two ideal batteries are placed in the configuration as above. Battery one has the potential E = 100 V and battery two has the potential Ez = 25 V while the resistances are given as R1 = 2N and R2 = 0.52. Find the potential at point Q if the potential at P is 50 V.
Consider the circuit shown in the figure below, where R, = 8.00 N, R, = 9.00 N, and Ɛ = 7.00 V. 10.0 N R2 5.00 N 2.00 N (a) Find the voltage (in V) across R,. 1' V (b) Find the current (in A) in R,. A
a. Write your understanding about the time constant for RC circuit. A capacitor is discharging through a resistor. If it takes a time T for the charge on a capacitor to drop to half its initial value, how long (in terms of T) does it take for the stored energy to drop to half its initial value? -e b. A 10-m-long wire has a resistance equal to 0.20 Q and carries a current equal to 5.0 A. (a) What is the potential difference across the entire length of the wire? (b) What is the electric-field strength in the wire?
Refer to Figure C If 0.050 A of current flows across the 300 ohms resistor, what is the voltage drop in 100-ohms resistor? Select one: a. 10 V b. 40 V c. 20 V d. 15 V
Figure P18.19 shows a circuit diagram. (R1 = 1550 , R2 = 430 , ΔV = 20.5 V) (a) Determine the current. (b) Determine the potential of wire A relative to ground. (c) Determine the voltage drop across the 1550 resistor.
An accumulator with U1=150 V and negligible internal resistance is connected to a voltage divider as shown in the figure. a) How big will the voltage U2 be if no external load is connected? b) How large will U2 be if a load with resistance RL = 2250.0 Ω is connected between A and B? c) How large will U2 be if a load with resistance RL = 9000.0 Ω is connected between A and B? d) How big will the effect be in the load c)?
answer a and b only..a12
please exaplain me step by step and clear hand wrriting please