Figure on the right shows the Moore model state diagram of a synchronous sequential circuit having one input (x) and one output (Z). a) Draw the state table of the synchronous sequential circuit, b) Derive the next state equations and the equation for the output. c) Derive the inputs expression if you are to use R-S flip flop as memory elements. d) Draw the logic diagram of the synchrnouse sequential circuit 1 D/0 A/0 C/1 B/0

Figure on the right shows the Moore model state diagram of a synchronous sequential circuit having one input (x) and one output (Z). a) Draw the state table of the synchronous sequential circuit, b) Derive the next state equations and the equation for the output. c) Derive the inputs expression if you are to use R-S flip flop as memory elements. d) Draw the logic diagram of the synchrnouse sequential circuit 1 D/0 A/0 C/1 B/0

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

A sequential circuit has two D flip-flops, two inputs x and y, and one output Z is specified by the following next-state and output equations A(t+1) = xA / +y / BB(t+1) = x/A/ +yB/Z = x(A / + B / ) (a) Draw the logic diagram of the circuit.(b) List he state table for the sequential circuit.(c) Draw the corresponding state diagram.
6) Draw the Mealy state diagram for a sequence detector that detects the sequence 0101 using a minimal number of states. The detector should also detect overlapping sequences. Design the circuit using D flip-flops. Draw the logic diagram. 7) Draw the Mealy state diagram for a sequence detector that detects the sequence 11001100 using a minimal number of states. The detector should also detect overlapping sequences.
2
Figure on the right shows the Moore model state diagram of a synchronous sequential circuit having two inputs (x and y) and one output (Z). a) Draw the state table of the synchronous sequential circuit, b) Derive the next state equations and the equation for the output. c) If you are to use either R-S or J-K flip flop as memory elements, derive the respective inputs. 00 11 01/0 01. 11 01 11 00 00/0 -011 11/1 00 10- 00 11- 10 xy 10/0 01
Q9
Q2: For the circuit shown in below, use (matlab, c++, or python) and Nodal Analysis to: a) Find the voltage across the current source 11 terminals b) Find the current through the resistance R1 c) Find the real and reactive Powers delivered by the current source 11 Find the real and reactive Powers consumed by the capacitor C2 d) 11 10 A RMS 50 Hz +35 Deg Z1 AM R2 402 Z4 R4 80 m Z2 L2 15 mH 12 7A RMS 50 Hz +74 Deg Zc1 C1 150 F R3 30 www w R6 40 Z6 L3 25 mH E1 100 V RMS - 40 Deg Z5 50 Hz www R5 20 Zc2 C2 200 F
• Design a sequential circuit with two T Flip Flops, A and B, and two inputs, E and x. If E=0, the circuit remains in the same state regardless of the value of x. When E=1 and x=1, the circuit goes through the state transitions from 00 to 01 to 10 to 11 back to 00, and repeats. When E=1 and x=0, the circuit goes through the state transition from 00 to 11 to 10 to 01 back to 00, and repeats
Q8/ Draw the state diagram and state table of a circuit that serially check non BCD code. The output of circuit is (Z=1 code is non BCD) valid every four clock cycles and for one clock period only.
Use the following state diagram and create the state table for a synchronous to detect the sequence. The circuit has a single input, x, and a single output z. The output is logic-1 whenever the input sequence 1001 is detected, logic-0 otherwise. Note that overlapping sequences are allowed, Create the initial state table, and the complete state table. Write the equations for all the state variables and the output z.
Design a sequential circuit (overlapping) with an input ‘x’. The pattern to be detected is the binary number that is equal to 01100 For example,the circuit detects the sequence 00010 . When the sequence is detected, the detector outputs z=‘1’ For this circuit:Draw the logic circuit for the datapath
b) Given a sequential circuit in Figure Q4b. Determine the next state equations, state table, state diagram, function that the circuit perform and revise the circuit by using T Flip Flops. SET SET Q K CLR Q K CLR Q CLK Figure Q4b
1- In the following sequential circuit. There are 2 D FF (A and B), 2 inputs (x and y), and 1 output z The output and next-states equations are given A(t+1) = x'y + xÃ B(t+1) = x'B + xA z= B c- Draw the corresponding state diagram.