Figure below shows a rod with mass M = 100 kg, cross section area A = 10 cm². The rod is supported by 4 springs having stiffnesses of k = 1 MN/m. A tip mass with m = 120 kg is attached to the rod. Assume x is the degree of freedom of the equivalent system. The Young's modulus, E, is not known. If the natural frequency of the equivalent mass-spring system is 40 Hz, determine the Young's modulus, E. Assume the length of the rod is L = 5 m. Find the nearest answer. k www. E, A, M k mw L k www. X 195 GPa 179 GPa 116 GPa 45 GPa 236 GPa 00000

Figure below shows a rod with mass M = 100 kg, cross section area A = 10 cm². The rod is supported by 4 springs having stiffnesses of k = 1 MN/m. A tip mass with m = 120 kg is attached to the rod. Assume x is the degree of freedom of the equivalent system. The Young's modulus, E, is not known. If the natural frequency of the equivalent mass-spring system is 40 Hz, determine the Young's modulus, E. Assume the length of the rod is L = 5 m. Find the nearest answer. k www. E, A, M k mw L k www. X 195 GPa 179 GPa 116 GPa 45 GPa 236 GPa 00000

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A metal polishing machine consists of a box full of ceramic particles mounted on the top of a shaker device, as shown in the figure below. The shaker runs at f = 7 Hz and carries an out of balance mass of mg = 50 kg at a distance of e = 0.01 m from the centre. The static deflection of the spring is A = 5 mm, the damping constant is c = 4000 kg/s and the total mass of the machine is m = 800 kg. Assume that gravitational acceleration is g = 9.81 m/s2. The amplitude of the steady state response of the system is: 1.58 mm 11.79 mm MA 1.74 mm 2.71 mm 5.46 mm Imm x
Figure below shows the single degree of freedom control surface/actuator system. The control surface has a moment of inertia J = 656 kg.m2 about the hinge, the effective actuator stiffness and damping values are k= 6 MN/m and c = 106 kNs/m respectively and the rotation of the control surface is A rad. The actuator lever arm has length a = 0.57 m. It is assumed that the main surface of the wing is fixed rigidly as shown in the figure. Assume that the system is hit by stone and hence move from rest position by an initial velocity of vo = 3.51 rad/s. Maximum amplitude response is: 0(t) k. d O 1.7 degrees O 1.25 degrees O 334 degrees O 2.56 degrees O 2.05 degrees
Solve
Three springs and a mass are attached to a rigid, weightless bar PQ as shown in the following figure. Find the natural frequency of vibration of the system. k2 m 10000
Answer with neat solution please. Thank you.
answer would be much appreciated
find the angular frequency w and the period T
A uniform plank of mass 2.29kg and length 39.6 cm is pivoted at one end, and the opposite end is attached to a spring of force constant 454N/m. The height of the pivot has been adjusted so that the plank will be in equilibrium when it is horizontally oriented as in the figure. Find the period of small oscillation about the equilibrium point. Answer in units of s.
i need the answer quickly
III) A relatively well-praised model for a car suspension is depicted in Figure 5: 4 4 Body Mass MW Suspension Mass b₂ ↑" Figure 5 - Model of the suspension of a car. Considering it is a system with two degrees of freedom, WRITE the equations that model the free vibrations of this system.
B3
Figure 2 shows an electrical motor with mass M=13 kg located at the middle of pinned-pinned beam. A damper with damping coefficient of c=59 N.s/m is also attached to the beam at point A . Considering Young’s modulus of the beam E=98 GPa, moment of inertia of the beam I=18 mm4, length of the beam L=1 m, unbalance mass of m0 =1.9 kg, eccentricity e=2.8 mm, and zero initial conditions, find the steady state amplitude of point A at resonance in millimetre (mm).