Figure below shows a rod that is free to rotate about its center of mass. A force F, = 10 N is applied at d, = 2 m from the COM and another force F,= 11 N is applied at d, = 3 m from the COM, as shown. The magnitude of the total torque about the axis of rotation is:

Figure below shows a rod that is free to rotate about its center of mass. A force F, = 10 N is applied at d, = 2 m from the COM and another force F,= 11 N is applied at d, = 3 m from the COM, as shown. The magnitude of the total torque about the axis of rotation is:

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

Force F = (-7.0 N)î + (5.0 N) ĵ acts on a particle with position vector7 = (4.0 m)î + (5.0 m) ĵ. (a) What is the torque on the particle about the origin, in unit-vector notation? = N: m (b) What is the angle between the directions of r and Torque is the cross product of a position vector (extending from a chosen point, here the origin, to the particle) and a force vector. Did you take the cross product in unit-vector notation? Do you remember how find the angle between two vectors by taking a dot product in both unit-vector notation and also in magnitude-angle notation? (You can similarly use a cross product to do this.) Do you remember how to find the magnitude of a vector from its components?
Consider an unsuccessful attempt to take off a tire using a wrench to loosen the bolts. Assume the wrench is 0.3m long and are you able to apply a 200N force Because the tire is flat you can only apply your force at a 60° angle. What is the torque at the center of the bolt. You find a tire jack and are now able to apply 200N of force at an 80° angle. Is the resulting torque more or less and what is the new torque.
find the total force experienced by the figure spire and the net torque on the spire pls dont skip steps
τ=rFsinθIs the version of torque we should now be using A ladder with a length of 2m and a mass of 5kg is resting against a wall so that it makes an angle of 60 degrees with the floor as shown above. Assuming that the mass of the ladder is distributed uniformly, what is the torque due to the weight of the ladder about its base? Remember, torque on an object will cause it to rotate if possible, even if the ladder is not rotating about the base (pivot point) the weight of the ladder would still cause it to rotate if the wall were to disappear. Hint: the angle should be between the FORCE and the RADIUS. Answer to 2 decimal places if possible
Given the picture attached: (a) Find the magnitude of the net torque on an axis about C perpendicular to the page. (b) Is this clockwise or counterclockwise?
A vertical rectangular object of uniform mass M=14.4kg has sides a=0.8m and b=D3.8m. It is pivoted from point O as shown in the figure below. If a constant force of F=87N, making an angle of 8=37° with the diagonal, is applied, determine the angular acceleration of the rectangle at the instant shown in the figure using Sl units. Express your answer with two decimal places. Please use the convention: Clockwise (+). Counterclockwise (-) when expressing your answer. Hint7: The moment of inertia of the rectangle obout on axis of rotation possing through its center of mass is - M(a²- Hint2: Don't forget the force of grovity!! Take g=9.80 m/s?. F B CM a
A proffesors office door is 1.3m wide, 2.3m high, 4.0cm thick, has a mass of 25kg, and pivots on friction less hinges. What is the smallest magnitude force that you need to apply to the door to give it an angular acceleration of 2 rad/s.
A thin rectangular plate is acted upon by 4 forces as shown. The 200 N makes an angle of 30 degrees with the horizontal. Calculate the net torque on this plate about the center A due to the four forces shown assuming there is no friction at the center. Note: (Angle at a is 30 degrees)
A 20 N force is applied at the end of a wrench that is 40 cm in length. The force is applied at an angle of 60° to the wrench. Calculate the magnitude of the torque about the point of rotation M.
A square is acted upon by the forces of 4, 6, 8, and 12N respectively along the four sides as shown. If the length of the side of the square is 0.5m, what is the resultant torque acting to rotate the square about an axis through A? 4N 12N 8N
A 3.0-m rod is pivoted about its left end. A force of 6.0 N is applied perpendicular to the rod at a distance of 1.2 m from the pivot causing a counter clockwise torque, and a force of 5.2 N is applied at the end of the rod 3.0 m from the pivot. The 5.2 N is at an angle of 30° to the rod and causes a clockwise torque. What is the net torque about the pivot? A 15 N.m B 0 N.m -6.3 N.m -0.6 Nxm D
The 25 N force F is applied to a corner of the rectangular plate of sides a = 0.50 m, b = 0.70 m. The angle θ is 37deg. a) Find the torque on the plate about i) the corner A, ii) the corner B, and iii) the corner C. Give both the magnitude and direction (clockwise or counterclockwise) in each case.