Figure below shows a beam acted upon a triangular distributed load. What is the magnitude and location of the equivalent concentrated load? 5 kN/m 4 m 4 m 5kN, 4m from the left 10KN, 2m from the left 10KN, 1.33 m from the left 20KN, 6.67 m from the right

Figure below shows a beam acted upon a triangular distributed load. What is the magnitude and location of the equivalent concentrated load? 5 kN/m 4 m 4 m 5kN, 4m from the left 10KN, 2m from the left 10KN, 1.33 m from the left 20KN, 6.67 m from the right

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Use image below You’re not solving anything for this question just drawing ! No math is required so do not write any equations! Draw the Free body diagram of the beam using the figure below
After greetings, How to solve this problem and what’s the final answer? AND THANK YOU VERY MUCH.
For the composite beam section in Figure Q2b, calculate the second moment of area (Ixx) about its centroid x-axis.
(a) The Figure la show the cross-section of a beam. All dimension are in cm. 10 2 10 Figure la (i) Calculate the centroid of the cross-section measured from the bottom of the cross section. (ii) Calculate the moment of inertia, I, for this cross-section. (iii)A pure bending moment of magnitude 1.0 kN.m is applied to the cross- section, generating compression above the neutral axis, and tension below. Calculate the maximum values of the tensile and compressive stress. (iv)The bending moment is removed. The same beam cross-section is now subject to a vertical shear force of 2.5 kN acting in the downward. Calculate the maximum horizontal shear stress. Where does it occur?
For the composite beam section in Figure Q6a, calculate the second moment of area about its centroidal x-x axis (Ixx centroid), where b₁ = 125.50 mm, b₂ = 25.75 mm, b3 = 36.35 mm, d₁ = 78.00 mm and d₂ = 24.00 mm Give your answer to 2 decimal places. b2 y dz b1 b3 Figure Q6a d1 X
8 kN/m 5 kN/m 1.5 m -0.75 m- 0.75 m- What is the magnitude of the resultant force equivalent the distributed load applied to this beam (kN)?
Consider the beam in the picture below: 7kN/m 5kN/m P N/m Section 1 Section 2 Section 3 - L/3 L/3 L/3 %3D Take P = the last four digits of your student number in N/m. If P<250 N/m then take P = 30OON/m instead. Take L = the third digit of your student number, reading left to reight. If this value is zero then take L = 2 Assume: The reaction at the Pin = V pin 47000L+9PL )N 54 The reaction at the Roller = Vroller = 61000L+9PL 54 and that both reactions act vertically upwards. a) Find an expression for the internal moment for Section 1. Show all working and any relevant free body diagrams. b) What is the maximum magnitude of the internal moment for Section 1? Mark sure you prove that the value you calculate is the maximum. c) Find an expression for the internal moment for Section 2. Show all working and any relevant free body diagrams. d) What is the maximum magnitude of the internal moment for Section 2? Mark sure you prove that the value you calculate is the maximum. e) Find an…
This question is made of two separate parts related to figures 1 and 2. 2 m F Figure 1 2 m in A direction L direction Figure 2 Figure 1 D A beam AB is supported by a pin at A and a roller at B. The beam is subjected to force F of 5 KN, making an angle a=400 with horizontal as shown in figure 1. The support reaction at pin A along x-axis is to the The support reaction at pin A along y-axis is The support reaction at roller B is M B Figure 2 A beams AB of length L-2 m is supported by a pin at A and a cable BC at point B. The beam is subject to an external moment M=200 N.m at B as shown in figure 2. The force in cable BC is and it is in
QUESTION 3 Given the beam shown in Figure Q3, calculate the reaction at point A, consider El to be constant. Wo Deformed Shape A B Figure Q3: Beam QUESTION 4 Determine the equivalent distributed load associated with the beam shown in Figure Q4. Determine the shear, moment, slope, and deflection equations, using the Macaulay functions and the singularity functions. 400N/m 20000NM 10m 5m 5m 2000N 2000N Figure Q4; Beam
You can assume that each shaded cell is 1m x 1m square. Forces are applied at either the top edge, middle, or bottom edge of the beam. A. Circle the beams which have equivalent loading to the top beam. Please give a brief explaning to learn why. Thank you!
Mechanics of deformable bodies: shear and moment diagram in beams. From the given figures below, draw the shear and moment diagram of the beam. Its either using the shear and moment diagram or area method. Please show the solving solution also.