Figure 3 shows the schematic of an embankment. The unit weight of the embankment material is 18.0 kN/m³. The embankment has a crest width of 15 m, a height of 30 m, and a 1:1.5 (V:H) slope. Find the vertical stress increases at Points A, B and C due to the embankment. 7.5m 7.5m 1 m K 5 m C 15 m 30 m A B 1.5 1

Figure 3 shows the schematic of an embankment. The unit weight of the embankment material is 18.0 kN/m³. The embankment has a crest width of 15 m, a height of 30 m, and a 1:1.5 (V:H) slope. Find the vertical stress increases at Points A, B and C due to the embankment. 7.5m 7.5m 1 m K 5 m C 15 m 30 m A B 1.5 1

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 15 m C IN 2 3.5 m 3.5 m BA 2 Unit weight y = 19 kN/m³ 8 m ↓

Q: A retaining wall 9 m high supports a cohesionless sandy soil with its face vertical as shown in…

A: A retaining wall,Total height = 9mq= 20kN/m²Yd= 16kN/m³

Q: A dam rectangular in cross–section has an upstream face vertical. Water is 20.4 m deep on the…

A: To Find :- factor of safety against sliding Given data :- Dam has rectangular section Base width =…

Q: Factor of safety against sliding * O 1.14 O 1.24 O 1.34 O 1.44 Factor of safety against overturning…

Q: Prob. In the dam shown, compute the following: 1. FS against overturning 2. FS against sliding 3.…

Q: An embankment for road traffic is required to be constructed with the following dimensions :Top…

A: Solution : From above question we get,

Q: A masonry dam of trapezoidal cross-section, with one end face vertical, has a thickness of 0.6 m at…

A: As per guidelines of bartleby, only 3 subparts are solved. If you want other parts to be solved ,…

Q: Problem (4.9): An embankment of (3m) high is to be constructed as shown in the figure below. If the…

A: Solution: Considering the Diagram 1. Vertical Stress at A: By considering the FigureσzA=σz1+σz2Left…

Q: The soil pressure distribution along the base of the gravity dam is triangular, with maximum stress…

Q: (Use The Figure (10.20) to find the solution of this question) Two embankments loads on silty clay…

A: Given, γleft = 11 kN/m3 γright = 13 kN/m3

Q: -2 m- 7 m 6 m. 4 m

Q: a. b. Check the stability of the dam per unit length (1 m) against: overturning, sliding, and…

A: Cross-section of concrete gravity dam Factor of safety=0.8 It is asked to check the stability of the…

Q: A long embankment 30 m wide is to be built on ground. The net vertical pressure applied by the…

A: Soil compaction refers to a mechanical process in which the soil gradually changes volume in…

Q: 3 A concrete gravity dam section is shown in the figure. Assuming unit weight of water as 10 kN/m²…

A: Given- Unit weight of water=10 kN/m3 Unit weight of concrete=24 kN/m3 Heads H=65 m & h=5 m, It…

Q: For the masonry dam shown in the figure below, k =5 x 10-3 m/day. a. Determine the seepage flow per…

Concept explainers

Methods to Determine Vertical Stress

The load applied to the soil is transferred to the underground. The presence of water at soil pores and solid grains above the soil are the primary components that are responsible for the effective load transfer. Due to the load acting, the internal component of the soil or the underground formations undergoes deformations or a tectonic shift. The amount of deformation depends upon the amount of load acting on the soil surface, which indeed, depends on the weight of everything present above the soil. Due to this, the underground soil element develops internal stresses which try to resist the tectonic changes.

Question

Figure 3 shows the schematic of an embankment. The unit weight of the embankment material y
is 18.0 kN/m³. The embankment has a crest width of 15 m, a height of 30 m, and a 1:1.5 (V:H)
slope. Find the vertical stress increases at Points A, B and C due to the embankment.
7.5m 7.5m
1 m
H
5 m
C
15 m
30 m
A
B
1.5

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The section of a gravity dam is as shown in the figure. Assume hydrostatic uplift "U' to vary uniformly from full hydrostatic uplift from the heel to zero at the toe. Determine the resultant acting at the base of the dam. Given the vertical forces, W1-224,640 Ibs., W2=44,928 Ibs., W3=71,884.8 Ibs., W4=56,160 lbs., U=131,040 Ibs., and a horizontal force F=112,320 bs. Resultant = 4 pts. W1 W2 WATER W4 10 W3 10 HEEL TOE
4. The masonry dam shown below has a crest width of 2m, base width of 15.0 m, and a height of 20m. Masonry weighs 23.54 kN/m³. If the allowable compressive stress at the toe is 345 kN/m², what is the permissible depth of the headwater? Assume there is no hydrostatic uplift. 2 m Elev. 8 m (crest) W.S. h/3 Elev. 0 m (base) Тое 15 m
You have been assigned to check the stability of a pond constructed in stiff saturated clay underlain by a layer of sand. The necessary information are given in the following figure. (i) Find effective stress at and determine the stability of cut under given condition. (ii) What should be water level into the pond to ensure factor of safety = 1. (Given that yw = 9.81 kN/m³) H = 5 m 7m KE T 3 m 2 m ↓ Saturated clay Sand Ysat 18 kN/m³ 6.5 m Ysat = 15 kN/m³
(Use The Figure (10.20) to find the solution of this question) Two embankments loads on silty clay soils layers as shown below. Unit weights of the left and right embankments are 11 and 13 kN/m², respectively. Determine the stress increase under the embankments at point A that are loaded at a depth of 4 m below the ground surface. Center ine 1V:1H y= 11 kN/m 5m 13 N/m Figure 10.19 Embankment loading 050 3.0 20 045 14 12 LO 0.40 09 07 0.35 06 0.30 04 025 020 02 a10 Figure 10.20 Osterberg's chart for determination of vertical stress 0.00 TT TT due to embank- 100 ment koading 327 HEAI
If in Figure 8.19 B₁ = 5.0 m, B₂=3.0 m, H = 4 m, z = 3 m, and the embankment applies a force of 137 kN/m2, the stress increase experienced 3 m (z = 3 m) below the bottom right corner point of the figure is, B₂- ** FIGURE 8.19 Embankment loading 105.58 kN/m² 62.34 kN/m² Ⓒ 150.78 kN/m² Ⓒ224.88 kN/m² -9-yl
(Use The Figure (10.20) to find the solution of this question) An embankment load on a silty clay soil layer as shown below. Determine the stress increase under the embankment at points A and B that are loaded at a depth of 6 m below the ground surface. 5m 1H:2V 1H:2V 1H:1V 8 m y-18 kN/m y-18 kN/m 6 m 4. y Figure 10.19 Embankment loading 050 TTTT 3.0 20 16 045 14 12 LO 040 09 07 035 06 030 05 04 - 025 03 020 02 015 a.10 Figure 10.20 Osterberg's chart for determination of vertical stress 0.00 due to embank- 0.01 0.1 10 100 ment loading 327
Subject: Soil Mechanics
Question 11 A rectangular channel with width = 10 meters and depth = 3 meters has a flow slope of 0.001 and roughness n = 0.025. The flow rate is 80 m/s. Determine the shear stress on the channel in Pascals
3.7 An embankment is shown in Figure P3.2. Given that B = 5m, H = 5m, m= 1.5, z = 3m, a= 3m, b = 4m, and y= 18kN/m³, determine the vertical stresses at A, B, C, D, and E. I Figure P3.2 B/2 8:2 NA S 121 Unit weight of soil embankment - Y ak B C D b E
A 4-m high embankment is to be constructed as shown in the Fig. 3 below. If the unit weight of soil used in the embankment is 19.0 kN/m3, calculate the vertical stress due to the embankment loading at points P1, P2 and P3. Use the Straight Line Law of Osterberg, 1957.
A 3 m high embankment is to be constructed as shown in the figure. If the unit weight of soil used in the embankment is 19 kN/m³, calculate the vertical stress due to the embankment loading at points P1, P2, and P3. 10.5 7.5 6 4.5 K CE 4.5 3.0 |y= 19 kN/m B 3.0 3.0 i-3.0 P3 Note: All dimensions are in metres P,
A 3 m high embankment is to be constructed as shown in the figure. If the unit weight of soil used in the embankment is 19 kN/m², calculate the vertical stress due to the embankment loading at points P1, P2, and P3. 10.5 7.5 6 4.5 CE 4.5 3.0 | y= 19 kN/m B 3.0 -3.0 -3.0 P3 Note: All dimensions are in metres P,