The soil pressure distribution along the base of the gravity dam is triangular, with maximum stress at the toe and zero at the heel. If the eccentricity of the resultant force is 1 m, thern the length of the base is:

The soil pressure distribution along the base of the gravity dam is triangular, with maximum stress at the toe and zero at the heel. If the eccentricity of the resultant force is 1 m, thern the length of the base is:

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter8: Stresses In A Soil Mass

Section: Chapter Questions

Problem 8.2P

See similar textbooks

Related questions

Q: maximum pressure intensity in the base of the dam (lb/ft3) b)minimum pressure intensity in the base…

A: We know thatF=ΥhAFH=62.4×0+972×97×1=293561 lb

Q: 1. A dam is triangular in cross-section with the upstream face vertical. The dam is 12 m high and 9…

A: Given Height of the Dam (H)= 12m Base width of dam (B)= 9m

Q: Find the pressure force acting on a dam 20 meters wide and 7 meters high and the place of action of…

A: Find pressure force and its location

Q: A masonry dam of trapezoidal cross section is 50 ft high. It has a thickness of 5 ft at the top and…

A: NOTE - Hi! Thank you for the question As per the honor code, We’ll answer the first question since…

Q: A dam is triangular in cross section with the upstream vertical. Water is flushed at the top. The…

A: ASKED: To determine the factor of safety against sliding and overturning for the given dam. Given,…

Q: 2. A concrete dam is triangular in cross section and 30 m high from the horizontal base. If water…

Q: An embankment load on a silty clay soil layer as shown below. Determine the stress increase under…

Q: A masonry dam has a coefficient of permeability in the vertical and horizontal directions of…

A: seepage flow is the flow of a fluid in permeable soil layers such as sand. Uplift pressure is also…

Q: A masonry dam of trapezoidal cross section, with one face vertical has thickness of 60cm at the top,…

Q: Q: The concrete dam shown in Figure is constructed on a soil with coefficient of permeability k =…

A: Given Data: k=0.06 cm/s γsat=19.8 kN/m3 H=8 m nf=3 nd=10

Q: trapezoidal channel is discharging 20.40 m^3/sec at a depth of 1.2 m and a base width of 6 m. The…

Q: (Flow Nets] (1 a. Seepage tiow rate (Q) per meter width of dam in L/s. b. Determine the uplift…

A: Appreciate if there is detailed work with explanation and finds you helpful for ease of…

Q: For the given dam as shown in the figure, determine: (a.) the factor of safety against sliding, (b.)…

A: Consider the following diagram:

Q: Please find the earth pressure at rest distribution value and resultant force on the retaining wall…

A: Given; H=12mγ=18.5 KNmγsat=22.5 KNmc=0 kPaq=25 kPa=25KNm2static side pressure coefficient=k0=0.5…

Q: 2. A deposit of clay is underlain a layer of sand. The clay layer is 2.8 m thick, void ratio = 0.67,…

A: For sand: e=0.51 Gs=2.65 H=3.5m For clay: e=0.67 Gs= 2.75 H=2.8m To find total lateral pressure at…

Q: A damn having a triangular section has a vertical face 24 m high and base 12 m wide. Use sg=2.4 a.…

A: (a) Height of water (h) Condition given is Maximum intensity of pressure at the toe = 2×Average…

Q: A masonry dam of trapezoidal cross section, with one face vertical has a thickness of 60 cm at the…

A: Given:- A masonry dam of trapezoidal cross section, with one face vertical has a thickness of 60 cm…

Q: The cross-section of a 22-ft high gravity dam is shown and is subject to water pressure standing 15…

A: Note :- as per our guidelines we are supposed to answer first three SUBPARTS only. So please repost…

Q: A masonry dam of trapezoidal cross section, with one face vertical has a thickness of 60 cm at the…

A: Given data: Thickness at top= 60 cm Thickness at base=3.70 m Height=7.40 m Unit weight of concrete…

Q: hs 2.6 tons per cubic meter. The coefficient of friction between the base and the foundation is 0.8.…

Q: 1. A dam is triangular in cross-section with the upstream face vertical. The dam is 12 m high and 9…

Q: dam has a trapezoidal cross-section 25 m high, crest width of 3 m and base length 18 m. The upstream…

Q: [Flow Nets] a. Seepage flow rate (Q) per meter width of dam in L/s. b. Determine the uplift pressure…

Q: A dam is triangular in cross section with the upstream vertical. Water is flushed at the top. The…

Q: Calculate the vertical stress at a depth of 50 ft below a point 10 ft oubide the corner (along the…

Q: Two embankments loads on silty clay soils layers as shown below. Unit weights of the left and right…

A: Boussinesq theory : Boussinesq (1885) devised a theory for calculating stresses and deformation…

Q: el of a trapezoidal dam having a dimension of 4 m on top, 18 m at the bottom and 24 high with water…

Q: rectangular channel carries a discharge of 18.10m3/s when flowing 1.5m depth. If the width of the…

Q: ) A uniform pressure of 150 kN/m acts on a 3 m*4.5 m rectangular rea. Since the point X is at the…

A: by using westergard theory Qz=wπz2 11+2rz23/2where,w=pointed loadz=depth below the midpointr=any…

Q: The face of a vertical dam has the shape of an isosceles trapezoid of altitude 11 ft, upper base 28…

A: Appreciate if there is detailed work with explanation and finds you helpful for ease of…

Q: a) Compute the vertical stress increment due to this uniform load at a depth of 5 m. below the…

A: Given ϑ = 16.97 kN/m3q = 300 kN/m3z = 5 md =4 m

Q: A concrete gravity dam has the following data: Maximum water level = 300.00 m Bed level = 220.00 m…

Q: A gate slanted 60 degrees from the horizontal with width = 1.6 m and height = 2.4 m is submerged by…

A: Given:- Width of gate = 1.6 m To find:- Pressure at the top of gate

Q: . If the stress at the toe of a trapezoidal dam is the maximum stress at the base and is equal to…

A: Given data, Eccentricity e = 0.0427 m Dam weight W = 993.6 kN Maximum stress at toe = 172.6675 kPa

Q: The height of a right-triangle shaped concrete gravity dam is 60 m with the 3 specific weight is…

A: 1- Forces acting on the dam body is shown below in the figure provided : Base of dam, B=1.5*60 = 90…

Q: EX: The uniformly distributed vertical load on the rectangular area is q1 =100 kN/m², and the…

Q: Water flows uniformly at a depth of 1.50 m in rectangular channel 4.0 m wide, laid on a slope, So=…

A: We know Average Shear stress is :τavg=γRSoR=APA=41.5=6m2P=4+21.5=7m

Q: An aquifer is overlain by 15 m of jointed rock. The density of the rock is 2500 kg/m. The density…

A: Note: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question…

Q: A water tower is constructed on a circular raft 5 m in diameter at a depth of 2 m below ground-level…

Q: A group of 4 point loads 3000 kN each are acting on the vertices of a rectangular area of length 5 m…

Q: A gravity dam of trapezoidal cross section shown below, with one face vertical and a horizontal base…

Q: A concrete dam retaining water is shown. Assuming that there is a hydrostatic uplift that varies…

Q: A 30-m high triangular dam has a vertical upstream face from the horizontal base. The depth of water…

Q: A 3 m high, 6 m wide rectangular gate is hinged at the top edge at A an is restrained by a fixed…

Q: A triangular dam has a vertical upstream face 30 m high from the horizontal base. The depth of water…

Q: 1. A masonry dam of trapezoidal cross section, with one face vertical and horizontal base. The dam…

Q: A masonry dam of trapezoidal cross section, with one face vertical, has a thickness of 1m at the top…

Q: A vertical, trapezoidal gate in the face of a dike is subjected to sea water pressure (s = 1.3) on…

Question

100%

a.
7 m

b.
8 m

c.
6 m

d.
9 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Initial concept.

VIEW

Apply formula & get the answer.

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Lateral earth pressure distribution against retaining walls

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

An embankment load on a silty clay soil layer as shown below. Determine the stress increase under the embankment at points A and B that are loaded at a depth of 6 m below the ground surface. Prob. 5 m 1H:2V 1H:2V 1H:1V 8 m Y=18 kN/m y=18 kN/m 6 m : B A
A concrete dam retaining water is shown. If the specific gravity of the concrete is 2.4, determine (a.) the location (from the toe) of the vertical resultant force acting at the base of the dam and (b.) pressure intensity at the heel and toe of the dam. Assume there is a hydrostatic uplift that varies uniformly from 80% hydrostatic head at the heel of the dam to zero at the toe. 3m 12 m 18 m 14 m 3m 3m B// 8 m 15m
2. A 2.4 diameter steel molding is lifted by 4 steel cables as shown. The mold weighs 3 kN/m. (a) what is the required diameter of wire that will not exceed the allowable stress of 120 MPa. and (b) if the wire diameter increase by 20%, find the vertical displacement of the molding. 4 m 2.4 m
A masonry dam (sp.gr. = 2.4) of trapezoidal cross-section is 20 m high. It has a thickness of 2 m at the top and 14 m at the bottomas shown in the figure.Coef. of friction under the foundation is 0.80 and assuming there is hydrostatic upliftthat varies linearly from one-half the hydrostatic head at the upstream edgeof the dam to zero at the downstream edge.Determine
For linear stress variation over the base of the dam of the figure, find where the resultant crosses the base and compute the maximum and minimum pressure intensity at the base. Neglect hydrostatic uplift. Note: unit weight of concrete is 2.5 times unit weight of water. 6m 19m 7'=2.5Y to 10 = 1· 3 m L 4 m - 11 m
Problem (2): Shaft BC is hollow with inner and outer diameters of 90 mm and 120 mm, respectively. For the loading shown Determine: • The minimum shearing stress in shaft BC. The maximum shearing stress in shaft BC. 0.9 m 0.7 m d 0.5 m A |120 mm TA = 6 kN - m В Tg = 14 kN m C D Tc = 26 kN - m Tn = 6 kN · m
For linear stress variation over the base of the dam of the figure, find where the resultant crosses the base and compute the maximum and minimum pressure intensity at the base. Neglect hydrostatic uplift. Ans.Pmax=555 kPa; Pmin=129 kPa Note: unit weight of concrete is 2.5 times unit weight of water. 6m 19m 1 Y'=2.5Y 1 30 40 ¹3 mi 4 m -11 m
The height of the reinforced concrete water dam in the figure is L width a. The unit weight of the body of the dam Su gola Betogarme su bendi is y=24 kN/m'. Since the height of the water lake is h and the lateral water thrust to the body is H=5h? kN/m, determine the maximum water height (hmax) to avoid 4. tensile stress at the base of the dam. (L=15m, a=7m) Note: Calculate for unit height (taking 1 m),
At the base of a gravity dam section, the vertical stress at the toe was found to be 6 MPa. Downstream face of the dam has a slope of 1H:√√2 vertical and assume there is no tail water. Maximum principal stress at toe of the dam is
A 50-kip vertical downward column load acts at the centroid of a 4-ft-square (4 ft by 4 ft) normal-weight concrete footing. The footing concrete has a unit weight of 150 pcf. The bottom of this footing is 3 ft below the level ground surface and the top of the footing is flush with the ground surface. The groundwater table is at a depth of 15 ft below the ground surface. Compute the bearing pressure at the base of the footing. Answer: Opsf Oksf A vertical force of 57.2 kips acts on a 4.0 ft x 4.0 ft area. Compute the induced vertical stress, Aoz, at a point 4.0 ft (zf = 4 ft) below the center (xf = 0 ft) of this square area using the following Boussinesq chart. Width = B Square Loaded Area 1.0 05 0.5 1.0
Determine the stress increase due to the embankment load at point A as shown in Figure 2. The unit weight of the embankment fill is 115pcf
Q. 1. (c) Determine the maximum base width of the elementary profile gravity dam with the following data : Specific gravity of the dam material Uplift intensity factor Coefficient of static friction Height of the dam = 2.4 = 1.0 = 0.80 = 20.0 m