Figure 1 shows a cube floating in a fluid. a) Derive an expression relating the submerged depth X, the specific weight of the cube, and the specific weight of the fluid. b) Derive an expression for the depth of submergence X that would ensure that the cube is stable in the position shown. c) Using the expression derived in (b), determine the required distance X for a cube 75 mm on a side.

Figure 1 shows a cube floating in a fluid. a) Derive an expression relating the submerged depth X, the specific weight of the cube, and the specific weight of the fluid. b) Derive an expression for the depth of submergence X that would ensure that the cube is stable in the position shown. c) Using the expression derived in (b), determine the required distance X for a cube 75 mm on a side.

Name: I am stuck on the third part, I’m not sure what to do next. A.....23Fl
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: I am stuck on the third part, I’m not sure what to do next. A.....23Fluidsurface1) Figure 1 shows a cube floating in a fluid.a) Derive an expression relating the submerged depth X, the specific weight of the cube, and thespecific weight of the fluid.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The University of Oklahoma School of Civil Engineering and Environmental Science spring 2024 Semester Problem 3 (30 pts.) ENGR 2411 Applied Engineering Statics Prerequisite Quiz Page 4 of a Your friend Dave loves hanging on the OU banner poles attached to the light poles on campus, this is despite your strong disapproval of their behavior. As an engineering student you are super concerned about the moment acting at the base of the light pole. What if Dave breaks the light pole! Calculate the moment acting about the base of the light pole (point O) when Dave is angled 45° from the horizontal banner pole. Dave weighs 120 lbs. Assume the force exerted by Dave on the banner pole is aligned with their arm that is holding onto the pole (ie. at 45°). B 15ft tf8 Disclaimer: Dave is fictional and does not represent any actual person.
(Use the following figure to answer questions b, c and d) T du dy Liquid A Liquid B b. What is the type of the two liquids? c. Explain how the shear force applied to each liquid affects its viscosity. d. Which liquid has higher apparent viscosity? Explain your answer.
1. In the operation of an internal combustion engine, the combustion gases expand in volume to make the piston move. As this occurs piston. Select the most correct phrase to go into this blank from these choices: gas particles move in the same direction as the motion of the A all the В almost all of the very few of the about half of the
An electric hot water heater consumes 3.1 kilowatts of electricity and converts it to heat. How long will it take the water heater to heat a 67 gallon tank of water from 10 degrees Celsius to 50 degrees Celsius? (1 kilogram of water is 0.37 gallons, 1 Calorie = 4200 J). It may be helpful to refer back to the weekly handout for guidance on this problem. Your final answer should be in minutes (rounded to the nearest 10 minutes).
help me pls
C Mississippi Jane is at it again! The big bad evil one has trapped her on an accelerating conveyor belt with a rolling pipe - or so it seems. The pipe is actually not there and instead to be added in during post production for the actress' safety. It is up to you to calculate the proper physics of the pipe so that the CGI pipe may look as realistic as possible. If the pipe is meant to have a mass of 500 (kg) and a mean radius of 0.55 m, determine the pipe's angular acceleration if the conveyor belt has an acceleration of 1.9 Assume the pipe does not slip on the conveyor belt and neglect its thickness. m 82 α= 3.5 X rad 2 сс UBC Engineering
can you write it in a paper? i dont know if its aA2 or aA2 or what
I have the answer but I need to much sure.
H4.
In our data run, we zeroed the force sensor at the cart's equilibrium position. Name the total force to stretch the spring F = ky. Name the force to stretch the spring to the cart's equilibrium position F, = ky,. Name the difference in the force to move the cart from the equilibrium position, F. So that F = F, +F, 23. Write the expression for F, in terms of y,, y, and k ?
i need the answer quickly
A gas filled in a piston-cylinder arrangement as shown in Figure 1 has a volume of 0.09 m³ at its initial equilibrium state. The gas is slowly heated through the bottom of the cylinder that allowed for the gas to expand at constant-pressure of 2095 kPa to a volume of 1.23 m°. The change in internal energy of the gas is 0.24 kJ. Ignoring the friction between the piston and the cylinder and assuming the atmospheric pressure any value from 90 to 110 kPa, of (a) Calculate the mass of the piston if the area of the piston is 0.047 m2 (b) For the gas as a system, evaluate work and heat transfer, each in kJ (c) For the piston as a system, evaluate work and change in potential energy, each in kJ Piston Gas