b)Figure 1 shows a center-tap rectifier circuit employing silicone diodes combined witha load network circuit consists of Zener diode, resistors R, = 1kN, R = 1kn andR, = 5k2. The waveform of the input voltage V,(t) = -V sinis depicted inFigure 2.Suppose V = 20V and winding ratio of the transformer is given bya:b =1:2,(i)Sketch the output waveform of V,(t).(ii)Sketch the output wave of V.(t).(iii)Determine the average de voltage of V, (t).V;VmSia : bIZM = 5mAIo37V(t)RL3 VLRoVoV: = 9 V-VmFigure 1Figure 2

Input voltage to primary side of transformer is -20sin(2πTt) By transformer action Voltage at…

Figure 1 shows a center-tap rectifier circuit employing silicone diodes combined with b) a load network circuit consists of Zener diode, resistors R, = 1k, R = 1k2 and (푸) R, = 5k. The waveform of the input voltage V,(t) =-V, sint is depicted in Figure 2. Suppose V, = 20V and winding ratio of the transformer is given by a:b=1:2, (1) Sketch the output waveform of V, (t). (ii) Sketch the output wave of V,(t). (iii) Determine the average dc voltage of V, (t). V Si a : b R I'ZM = 5mA + 3T V:(t) RL VL Ro Vo V = 9 V Figure 1

Figure 1 shows a center-tap rectifier circuit employing silicone diodes combined with b) a load network circuit consists of Zener diode, resistors R, = 1k, R = 1k2 and (푸) R, = 5k. The waveform of the input voltage V,(t) =-V, sint is depicted in Figure 2. Suppose V, = 20V and winding ratio of the transformer is given by a:b=1:2, (1) Sketch the output waveform of V, (t). (ii) Sketch the output wave of V,(t). (iii) Determine the average dc voltage of V, (t). V Si a : b R I'ZM = 5mA + 3T V:(t) RL VL Ro Vo V = 9 V Figure 1

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

FN.Q5 – A Transformer has primary windings as Np = 720 and secondary windings as Ns = 144. Its secondary voltage is Vs = 42V and output power of the transformer is PN= 2750W. The value of loses powers are Pcu = 52,5W and Pre = 39W. The resistance of loads are RLI = 1,660 and R12 = 1,950. (Pcu and PFE will be considered to be approximately the same in different load values.) Determine the following values in the circuit: Primary winding Secondary winding N, turns Ng turns Magnetic Flux, Primary current ISL Secondary 4 current Primary voltage ISL1 (ISL2 Secondary voltage RL1 R12 Transformer Core (a) the primary voltage VP, (b) the secondary load current Isı, if the transformer is rated at RLI and R12, (c) the primary load current IpL, (d) the load resistance R13 when the transformer is fully loaded by third in parallel, (e) efficiency n (fully loaded)
5) A flyback converter has an input of 45 V, an output of 15 V, a duty ratio of 0.4, and a switching frequency of 80 kHz. The load resistor is 15 Q. (a) Determine the transformer turns ratio. (b) Determine transformer magnetizing inductance Lm such that its maximum current is 120% of its average current.
Draw the scheme of a single-phase transformer with two secondary windings and mark the main symbols and quantities. Write the formulas to determine the total power P1, the transformation ratios and the primary current I1.
Please do it fast...
A transformer having a nominal voltage = 399V and a no load voltage = 420V at its secondary, the short circuit current at the secondary of this transformer in function of its nominal current will be: Select one: Isc=10*In None of these Isc=30*In Isc=20*In Isc=40*In
I need the answer as soon as possible
56. A single phase thyristor adjust line spacing converter with a resistive load is shown below: V₂ = V₂ sinet SCR ER V₂ If the supply voltage is 230V (rms) at 50 Hz, calculate ripple factor for firing angle a -45° and R = 100 Q. (A) I (C) 1.21 (B) 1.11 (D) 1.44
by High Voltage
For the given circuit below, a step down transformer gives an RMS voltage of 230 V/ 13.7- 0-13.7 V with a load resistance of 2.2 Kiloohms. Assume Silicon diodes are used. Determine the Peak Inverse Voltage of the diode. D. ст R 38.74 O 19.38 O 24.57 O 30.23 leeee
A voltage multiplier has 12 stages Capacitances, all equal to 0.08 μF. Thesupply transformer secondary voltage is 150 kV at a frequency of 100 Hz. Load current 0,006A.What is the percentage ripple, the regulation and the optimum number of stages for minimumregulation or voltage drop.
Determine the regulation of a transformer in which thepercentage resistance drop is 1% and the percentagereactance drop is 5% when the power factor 0.8 leading.
Q5. A 20 kVA, 2000/200-V, 50-Hz transformer has a high voltage winding resistance of 0.2 2 and a leakage reactance of 0.240. The low voltage winding resistance is 0.05 and the leakage reactance is 0.02 2. Find the equivalent winding resistance, reactance and impedance referred to the (i) high voltage side and (ii) the low-voltage side. (Draw the related equivalent circuits)