Figure 1 below shows a flow system that has two inlets and two outlets. If the total inlet mass flow rate is given by m. Inlets 1 and 2 have gauge pressures of 50kPa and 70 kPa, respectively. Calculate the force needed to anchor the piping system in its place. 10) cm 5) cm 7) cm 7) cm 50) kg/s DI = D2 D3 D4 = m = ( V2 = V/2 D3 30 D2 D4

Figure 1 below shows a flow system that has two inlets and two outlets. If the total inlet mass flow rate is given by m. Inlets 1 and 2 have gauge pressures of 50kPa and 70 kPa, respectively. Calculate the force needed to anchor the piping system in its place. 10) cm 5) cm 7) cm 7) cm 50) kg/s DI = D2 D3 D4 = m = ( V2 = V/2 D3 30 D2 D4

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Flow of oil (Left to Right) Q = 8.5 L/s Fluid below is mercury; SG = 13.6 Rest is filled with oil SG= 0.80 Find the h, 37.5 mm y-h1 hi 25 mm 2 3 _X=h₂
Write your step by step solutions.
Use four decimal places in all solution
What pressure, p₁, is needed to produce a flowrate of 0.09 ft3/s from the tank shown in the figure below? Assume d = 0.071 ft. P1 = Mi ! psi Air P1 Gasoline diameter d→ Salt water SG = 1.1 2.0 ft 3.6 ft
The figure below shows a fabricated assembly made from three different sizes of standard steel tubing listed in Appendix G.2. The larger tube on the left carries 0.075 m3/s of water. The tee branches into two smaller sections as shown. Reducing tee Flow 100-mm OD x 3.5-mm wall steel tube - 160-mm OD x 5.5-mm wall steel tube - 50-mm OD x 1.5-mm wall steel tube Required If the velocity in the 50-mm tube is 10.00 m/s, what is the velocity in the 100-mm tube to the nearest 1000th?
A pump draws water from reservoir A and lifts it to reservoir B as shown in the figure. The loss of head from A to 1 is four times the velocity head in the 50mm pipe and loss of head from 2 to B is 15 times the velocity head in the 100mm pipe. The pump discharge rate us 50 liters per second. Determine the following: A. Power delivered by the pump in KW B. Pressure head at pt. 1 in meter C. Pressure head at pt 2 in meter
Given A fluid with sg = 0.74 is flowing at 0.089 m3/s in the fabricated tube shown in the figure. The pressure in the tube before the contraction is 475 kPa. Refer to Appendix G.2. Flow 80-mm OD x 2.8-mm wall steel tube 160-mm OD x 5.5-mm wall steel tube Required Calculate the pressure in the smaller tube, to the nearest 10th. Your Answer:
The suction side of a pipe system is as shown in the figure. The pump discharges 495 gpm of water under a total head of 100 ft at 40°F. Atmospheric pressure = 32.7 ft of water. If the required NPSH is 9 ft, will there be a cavitation problem? Please note that 1 cfs equals 449 gpm. 12 ft 6 ft Diameter L = 300 ft Steel = 10 in 5
Don't worry about the table
Given A pipe is tapered to form a nozzle as shown in the figure, and the nozzle produces a jet velocity of 102 ft/s. 1.0-in diameter Flow 0.75-in diameter Required Calculate the required pressure in the larger section to produce the jet velocity given, in psi to the nearest 10th. The fluid is water at 180°F (Appendix A). Your Answer:
Three pipes are connected in parallel, The difference in heads in each pipe is 40 m. Pipes Diameter (cm) Length (m) Friction factor 1 15 500 0,02 2 10 450 0.03 3 20 800 0,025 3. Determine the flow in pipe 3.
A 1-m³ volume of water is contained in a rigid container. Estimate the change in the volume of the water when a piston applies a pressure of 33 MPa. m³