Fig. shows a steel bar 900 mm long; its two ends are 40 mm and 30 mm in diameter, the length of each rod is 200 mm. The middle portion of the bar is 15 mm in diameter and 500 mm long. If the bar is subjected to an axial tensile load of 15 KN, find its total extension, take E = 200 GPa 15mm "

Fig. shows a steel bar 900 mm long; its two ends are 40 mm and 30 mm in diameter, the length of each rod is 200 mm. The middle portion of the bar is 15 mm in diameter and 500 mm long. If the bar is subjected to an axial tensile load of 15 KN, find its total extension, take E = 200 GPa 15mm "

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An aluminum bar having a cross-sectional area of 160 mm? carries the axial loads as shown in the Figure below. Assume that the bar is suitably braced to prevent buckling and E = 70000 MPa. The length of each bars are follow: B, = 0.8 m; B2 =D 1.0 m; B;= 0.6 m. Determine the axial load acting on bar B, in kN. 35KN B1 B2 B3 10KN 15KN 30KN A 35 B) 20 C) 10 (D) 5
Bronze Steel Steel W = 40 kips %3D 2 ft 2 ft 2.
4.48 A thin rod of 10 mm diameter is subjected to a tensile force of 7850 N. What are the principal: stresses and maximum shear stress? (a) 70 MPa, 50 MPa, 10 MPa (b) 100 MPa, zero, 50 MPa (c) 100 MPa, 50 MPa, 25 MPa (d) 100 MPa, zero, zero
Q1: The beam shown in Figure 1 is subjected to a vertical force Pv and a horizontal force Ph. The data for Pv, Ph, a,L,and e are shown in Table 1. Determine the maximum compressive and tensile stresses under the vertical force (at a distance a from the left support.) Pv = 80k N a = G0o 6 omm e %3D 26 K N 120 mm L =3600 mm Figure 1 250 mm
A rigid bar XYZ as shown in the figure below is hinged at X and is supported at Y. If the stress in the steel rod is limited to 150 ksi, determine the largest possible load P that can be applied at point Z.
Consider the truss shown in (Figure 1). Suppose that F = 12 kN. gure B C D 12 m, 6 @ 2 m E F 3 m Part A Determine the force in member CD and state if this member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. FCD = Submit Part B FCJ = Submit __ Part C μA Value Request Answer Determine the force in member CJ and state if this member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. μA Value Units Request Answer ? Units ? Determine the force in member KJ and state if this member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension.
O A steel specimen of 12 mm diameter extends by 6.31 x 10-2 mm over a gauge length of 150 mm when subjected to an axial load of 10 KN. The same specimen undergoes a twist of 0.5° an a length of 150 mm over a twisting moment of 10 N-m. Using the above data, determine the elastic constants E,µ,G and K.
d = 100 mm x = 50 MPa Fig. 01 d = 75 mm T = 80 MPa 02 Determine the smallest allowable diameter brass rod, of length 3.0m, if the rod is to be twisted through one complete revolution without exceeding a shearing stress of 50 MPa. For brass, G = 39 GPa.
Situation 2: A steel rod is inserted into a wooden block as shown. Further, two cables (one on each end) are attached to the rod where it carries a bar with negligible weight. Determine the maximum allowable force P in Newtons based on the stress and strain parameters given below. Wooden Block: Shear strength capacity = 10 MPa Bearing strength capacity = 15 MPa Normal strength capacity = 40 MPa Steel Rod: Shear strength capacity = 15 MPa 40 mm 2500 mm 100 mm 120 mm 'I 220 mm 12 mm dia.
i need the answer quickly